VAIN's G3
From Fen Spinner Wiki
More actions
VAIN's G3 designate each g3 mods made by JEB spinner VAIN.
Construction of VAIN G*2
Parts needed
List from Ponkotu's blog[1]:
- 2x G3 (1 barrel, 2 grip and 1 plastic tip)
- 1x Zebra D1k (tip, grip and cap)
- 1x Pilot Frixion Colors (cap and rubber part)
- 1x Pilot G1 (tip)
- 3x Pentel Hybrid Gel Grip (3 tips and 1 backplug)
- 1x Dong-A Anyball (grip)
- 1x Uni-Ball Lakubo (grip)
- a stripe of any grip
Additional Items
- Tape
- An insert
Text tutorial
Preparation
- Cut 2x 2 blocks of Anyball grip.
- Prepare the G3 barrel by filing the square and front bump.
- Cut the D1k grip to 7 blocks.
Assembly
Front side
- Put the Rubber part of the Frixion cap inside the front of the G3 barrel.
- Stack the tips in this order: plastic G3, Signo, and g1.
- Put 2 Anyball grip on the g3 barrel, then add the Lakubo grip (flat side first).
- Push the tip stack inside the Lakubo grip.
Cap side
- Put a G3 grip into another one
- stack the 3 HGG tip (wrap some tape around it) and put it inside the Frixion cap.
- Push the small grip in the frixion cap.
- Put both G3 grips inside the frixion cap.
- Connect the G3 body to the Frixion cap.
Construction of VSG3
Parts needed
List from VAIN's Youtube channel:
- 1x G3 (barrel, grip, Rubber stopper inside the cap, and plastic tip)
- 1x Zebra Jim-knock (tip and grip )
- 1x Uni-Ball Lakubo (grip)
- 1x Pilot Frixion Colors (cap)
- 1x Pilot Hi-Tec C Maica (tip)
- 1x Signo DX (tip and grip)
Additional Items
- Tape
- An insert
Text tutorial
Preparation
- Prepare the G3 barrel by filing the square and front bump.
- Cut the Signo DX grip to 9mm.
- Cut 1mm of the Jimknock grip (Flat part).
Assembly
Front side
- Put the rubber stopper of the G3 cap inside its plastic tip.
- Stack the tip in this order: G3 (screwed on the body), Jimknock then Signo.
- Add the grip in this order: 9mm of Signo DX, then the Lakubo grip (flat side first) (tipstack should be covered).
Cap side
- Fold the G3 grip over itself (lengthwise) and put it into the Jimknock grip.
- Empty the Frixion cap.
- In this order, put inside the Frixion cap: Hitec tip and Jimknock grip
- Put the equivalent of 5 dimple of length of DX grip onto the Frixion cap.
- Connect the G3 body to the Frixion cap.
Video tutorial
Video tutorial by VAIN.
Construction of Flare Vain G3
Parts needed
List from VAIN's Youtube channel[2]:
- 1x G3 (barrel, grip, Rubber stopper inside the cap, and plastic tip)
- 1/2x Zebra Hyper Jell (grip)
- 1x Zebra Jimnie (cap)
- 1x Pentel Hybrid Gel Grip (tip and grip)
- 1x Pilot Frixion Colors (Rubber part on the end of the cap)
- 1x Pilot Hi-Tec C (tip)
- 1x Ohto Needlepoint (grip)
- 1x Pentel Hybrid Gel Roller (tip)
- 1x KILAT Oil-based Ballpen Knock type (grip)
- (Can be subbed with Anyball grip)
Additional Items
- Tape
- An insert
Text tutorial
Preparation
- Prepare the G3 barrel by filing the square and front bump.
- Cut the clip of the Jimnie cap.
- Cut 2.9cm of Hyper Jell grip.
- Cut 5mm of the other Hyper Jell grip.
- Cut 1 ring of KILAT Oil-based pen.
- Cut 1.1 cm of Ohto Needlepoint grip.
Assembly
Front side
- Put the 1.1cm of Needlepoint grip on the front of the G3 barrel.
- Stack the tip on the G3 front following this order: G3 (screwed on the G3 front), HGR, G3 rubber part, and Hitec C.
- Cover the remaining visible part of G3 and the tip stack with a full HGG grip (ring side first).
Cap side
- Put the Frixion rubber part inside the HGG tip.
- Roll/fold the G3 grip and put it inside the 2.9cm of Hyperjell grip.
- Add 5mm of Hyperjell grip inside the 2.9cm of Hyperjell grip.
- Inside the Jimnie cap, push in this order: The HGG tip (tip facing the exterior), the Hyperjell grip (side with the G3 grip first), and 1 ring of Anyball.
- Wrap some tape on the back of the G3 body and connect it to the Jimnie cap.
Video tutorial
Video tutorial by Vore-Tex.
Construction of Di*vain
Parts needed
List from VAIN's blog[2]:
- 1x G3 (barrel and plastic tip)
- 1x Zebra Jimnie (cap)
- 1x Uni-Ball Lakubo (grip)
- 1x Pilot SuperGrip (grip)
- 1x Uni-Ball Signo (tip)
- 1x Ohto Needlepoint (grip)
- 2x Pentel Hybrid Gel Roller (tip)
- 1x Pentel RSVP (grip)
- 1x Dong-A Anyball (grip)
- 1x Zebra Tect 2way (1 Silicone ring)
Additional Items
- Tape
- An insert
Text tutorial
Preparation
- Prepare the G3 barrel by filing the square and front bump.
- Cut the clip of the Jimnie cap.
- Cut 6mm of Needlepoint grip.
- Cut 3 blocks of Supergrip grip.
- Cut 1 block of Anyball grip.
Assembly
Front side
- Add 3 blocks of Supergrip on the G3 front.
- Overgrip the Supergrip ring closest to the front with one block of Anyball grip.
- Add 1 Ring of Tect.
- Stack the tip in this order: Signo, G3 and HGR. Wrap some tape around it to secure it.
- Cover the remaining visible part of G3 and the tip stack with a full Lakubo grip (flat side first)
Cap side
- In this order, add in the Jimnie cap: HGG tip, HGR tip, a whole RSVP grip (side without ring first), and 6mm of Needlepoint grip.
- Wrap some tape on the back of the G3 body and connect it to the Jimnie cap.