K7 Hybrid: Difference between revisions
From Fen Spinner Wiki
More actions
No edit summary |
Apply independent tutorial corrections; retain disputed construction pending editor decision |
||
| Line 29: | Line 29: | ||
===Text tutorial=== | ===Text tutorial=== | ||
====Preparation==== | ====Preparation==== | ||
# Remove the clip of the Jimnie cap. | # Remove the clip of the Jimnie cap. | ||
| Line 38: | Line 37: | ||
====Assembly==== | ====Assembly==== | ||
=====Front side===== | =====Front side===== | ||
# Stack the Hi-Tec-C tip on the plastic G3 tip, then stack the Signo tip onto the Hi-Tec-C tip (add Teflon tape between each tip to stabilize the assembly) | # Stack the Hi-Tec-C tip on the plastic G3 tip, then stack the Signo tip onto the Hi-Tec-C tip (add Teflon tape between each tip to stabilize the assembly).<br>[[File:Step-2K7H.jpg|left|thumb|300px|]]<br clear=all> | ||
# | # Fit the front components in this order: ring, 0.9 cm Hyperjell grip, ring, 1 cm Signo Broad grip, ring. | ||
# Add two wraps of Vinyl tape on the ungripped part of the G3 front (should stop at the base of the Signo tip).<br>[[File:Step-5K7H.jpg|left|thumb|300px|]]<br clear=all> | # Add two wraps of Vinyl tape on the ungripped part of the G3 front (should stop at the base of the Signo tip).<br>[[File:Step-5K7H.jpg|left|thumb|300px|]]<br clear=all> | ||
# Add the Signo DX grip on the front of the G3 barrel. | # Add the Signo DX grip on the front of the G3 barrel. | ||
=====Cap side===== | =====Cap side===== | ||
# | # Place the Signo tip onto the HGG tip (using Teflon tape if needed), then put both tips inside the Japanese Jimnie cap.<br>[[File:Step-6K7H.jpg|left|thumb|300px|]]<br clear=all> | ||
# Put 0.3 cm of Signo Broad grip then the remaining Hyperjell inside the Japanese Jimnie cap.<br>[[File:Step-7K7H.jpg|left|thumb|300px]]<br clear=all> | # Put 0.3 cm of Signo Broad grip then the remaining Hyperjell inside the Japanese Jimnie cap.<br>[[File:Step-7K7H.jpg|left|thumb|300px]]<br clear=all> | ||
# Add tape on the G3 body then connect it to the Jimnie cap. | # Add tape on the G3 body then connect it to the Jimnie cap. | ||
===Video tutorial=== | ===Video tutorial=== | ||
Latest revision as of 22:37, 3 October 2026
The K7 Hybrid is a single sided mod made by iMatt. This mod is a hybrid between a SEVEN g3 and a KUzu G3.
Construction
Parts needed
List from UPSB v3[1]:
- 1x G3 (all parts)
- 1x Signo DX (grip and tip)
- 1x Signo Broad (grip and tip)
- 1x Pentel Hybrid Gel Grip (tip)
- 1x Pilot Hi-Tec-C (tip)
- 1x Hyperjell (cap and grip)
- 1x Dong-A Anyball (grip)
- 1x Japanese Jimnie (cap)
- Optional: 3x Penwish rings
=Additional items
- Tape
- An insert
Original insert
Text tutorial
Preparation
- Remove the clip of the Jimnie cap.
- Prepare the G3 barrel by filing the square and front bump.
- Cut 0.9 cm of Hyperjell grip.
- Cut 1 cm and 0.3 cm of Signo Broad grip.
Assembly
Front side
- Stack the Hi-Tec-C tip on the plastic G3 tip, then stack the Signo tip onto the Hi-Tec-C tip (add Teflon tape between each tip to stabilize the assembly).
- Fit the front components in this order: ring, 0.9 cm Hyperjell grip, ring, 1 cm Signo Broad grip, ring.
- Add two wraps of Vinyl tape on the ungripped part of the G3 front (should stop at the base of the Signo tip).
- Add the Signo DX grip on the front of the G3 barrel.
Cap side
- Place the Signo tip onto the HGG tip (using Teflon tape if needed), then put both tips inside the Japanese Jimnie cap.
- Put 0.3 cm of Signo Broad grip then the remaining Hyperjell inside the Japanese Jimnie cap.
- Add tape on the G3 body then connect it to the Jimnie cap.
Video tutorial
Video tutorial by Super Nova.