Charcoal Latte: Difference between revisions
From Fen Spinner Wiki
More actions
m Copyedit: spelling and grammar |
|||
| (One intermediate revision by the same user not shown) | |||
| Line 29: | Line 29: | ||
===Text tutorial=== | ===Text tutorial=== | ||
====Preparation==== | ====Preparation==== | ||
# | # Disassemble the Stalogy and keep only its barrel. Remove the lip at the front. | ||
# Cut | # Cut a 3 cm section from the rear of each Color Twin barrel. Keep these rear sections. | ||
# Cut | # Cut two 2 cm sections of Bic Round Stic barrel for the connectors. | ||
# Cut | # Cut two 1 cm sections of Signo DX grip. | ||
====Assembly==== | ====Assembly==== | ||
# | # Insert a Bic connector into each end of the Stalogy barrel. Sand the connectors slightly if needed for a snug fit. | ||
# | # Insert a leftover grip into each Bic connector. Add a decorative grip over each connector if desired. | ||
# Fit a 1 cm Signo DX grip section over the uncut rear end of one Color Twin section. | |||
# | # Fit a full Opt grip next to the DX grip, dimpled end first. Stretch the Opt grip from the inside if needed before fitting it. | ||
# | # Insert a Playbalance weight into the exposed end of the Opt grip. | ||
# | # Insert a Geloplus grip into the Playbalance weight. | ||
# | # Insert a HGG backplug into the Geloplus grip. Wrap tape around the backplug if it fits loosely.<br>[[File:Charcoal Latte structure.jpg|left|thumb|300px]]<br clear=all> | ||
# | # Attach the Color Twin section to a Bic connector. | ||
# Repeat on the other side. | # Repeat the end assembly on the other side. | ||
==References== | ==References== | ||
<references /> | |||
[[Category:Pen Mods]] | [[Category:Pen Mods]] | ||
Latest revision as of 18:35, 1 October 2026
The Charcoal Latte is a personal double-sided mod of THPSC spinner Coffy.
Construction
Parts needed
List from Coffy's post[1]
- x1 Nitoms Stalogy (barrel)
- x1 Bic Round Stic (barrel)
- x2 Dr. Grip Playbalance (weight)
- x2 Quantum Geloplus+ (grip)
- Can be substituted with any other small grip
- x2 Pentel Color Twin (2 bodies)
- x2 Pentel Hybrid Gel Grip (backplugs)
- x1 Signo DX (grip)
- x2 Pilot Opt Shaker (grips)
- x2 decorative grip
- Coffy uses 6 Tect ring from Eno
- x2 Leftover grip
- Coffy uses the square part of G3 grip
Text tutorial
Preparation
- Disassemble the Stalogy and keep only its barrel. Remove the lip at the front.
- Cut a 3 cm section from the rear of each Color Twin barrel. Keep these rear sections.
- Cut two 2 cm sections of Bic Round Stic barrel for the connectors.
- Cut two 1 cm sections of Signo DX grip.
Assembly
- Insert a Bic connector into each end of the Stalogy barrel. Sand the connectors slightly if needed for a snug fit.
- Insert a leftover grip into each Bic connector. Add a decorative grip over each connector if desired.
- Fit a 1 cm Signo DX grip section over the uncut rear end of one Color Twin section.
- Fit a full Opt grip next to the DX grip, dimpled end first. Stretch the Opt grip from the inside if needed before fitting it.
- Insert a Playbalance weight into the exposed end of the Opt grip.
- Insert a Geloplus grip into the Playbalance weight.
- Insert a HGG backplug into the Geloplus grip. Wrap tape around the backplug if it fits loosely.
- Attach the Color Twin section to a Bic connector.
- Repeat the end assembly on the other side.
