Beige g3: Difference between revisions
From Fen Spinner Wiki
More actions
mNo edit summary |
m Copyedit: clarify component names |
||
| (One intermediate revision by one other user not shown) | |||
| Line 13: | Line 13: | ||
===Parts needed=== | ===Parts needed=== | ||
List from Beige's blog:<ref | List from Beige's blog:<ref>[http://beige72.blog.fc2.com/blog-entry-54.html tutorial from Beige's blog]</ref> | ||
* 1x [[Pilot G3|Plastic G3]] (Barrel, tip) | * 1x [[Pilot G3|Plastic G3]] (Barrel, tip) | ||
* 1x [[Zebra Hyper Jell]] (Grip) | * 1x [[Zebra Hyper Jell]] (Grip) | ||
| Line 29: | Line 29: | ||
===Text tutorial=== | ===Text tutorial=== | ||
====Preparation==== | ====Preparation==== | ||
# Cut the clip of your | # Cut the clip of your Hyper Jell cap, and sand if necessary. | ||
# Remove the backplug, tip, grip, and ink of the Plastic G3, then sand down the nubs on the front. | # Remove the backplug, tip, grip, and ink of the Plastic G3, then sand down the nubs on the front. | ||
# Cut 3-4mm of the smooth part of the G3 grip. | # Cut 3-4mm of the smooth part of the G3 grip. | ||
| Line 45: | Line 45: | ||
# Add 3 blocks of Supergrip in the Ballsign cap, then put it inside the Hyperjell cap. | # Add 3 blocks of Supergrip in the Ballsign cap, then put it inside the Hyperjell cap. | ||
# Add an optional insert to the barrel. | # Add an optional insert to the barrel. | ||
# Add the 0.5cm-long | # Add the 0.5cm-long HGG grip on the back of the g3 body, then connect it to the Hyperjell cap. | ||
==References== | ==References== | ||
Latest revision as of 13:05, 27 August 2026
Construction
Parts needed
List from Beige's blog:[1]
- 1x Plastic G3 (Barrel, tip)
- 1x Zebra Hyper Jell (Grip)
- 1x HGG (tip, Grip)
- 1x Uni-Ball Signo (tip, grip)
- 1x New Sakura Ballsign (cap)
- 2x Pilot Supergrip（Grips）
- 1x Pilot CHOOSE（Plastic tip)
- 1x Pilot Hi-Tec-C（Tip）
Additional Items
- Tape
- An insert
Text tutorial
Preparation
- Cut the clip of your Hyper Jell cap, and sand if necessary.
- Remove the backplug, tip, grip, and ink of the Plastic G3, then sand down the nubs on the front.
- Cut 3-4mm of the smooth part of the G3 grip.
- Cut 3 blocks, 4 blocks, and 2 blocks of Supergrip grips.
- Cut 5mm of the HGG grip.
Assembly
- Put 3 blocks of Supergrip inside the front of the G3 barrel.
- Add the small segment of g3 grip, then 4 stripes on Supergrip on the front.
- Tip stack these tips in this order: Signo < HGG < Pilot choose (Pilot choose is under), add tape so it's stable.
- Put the tip stack in the Hyperjell grip and add the Hyperjell grip on the front.
- Put the Hi-Tec C tip inside the Hyperjell cap, then push 2 blocks of Supergrip.
- Add 3 blocks of Supergrip in the Ballsign cap, then put it inside the Hyperjell cap.
- Add an optional insert to the barrel.
- Add the 0.5cm-long HGG grip on the back of the g3 body, then connect it to the Hyperjell cap.