N900 Vortex: Difference between revisions
From Fen Spinner Wiki
More actions
Publish wording review of existing tutorial; retain construction without adding a source, per editor direction |
|||
| (One intermediate revision by the same user not shown) | |||
| Line 8: | Line 8: | ||
|cog= cop | |cog= cop | ||
}} | }} | ||
The '''台制戰彈''' is a double sided mod made by [[TWPS]] spinner [[Joey]]. The name can be roughly translated as "Taiwan-made Warheads". | The '''台制戰彈''' is a double-sided mod made by [[TWPS]] spinner [[Joey]]. The name can be roughly translated as "Taiwan-made Warheads". | ||
==Construction== | ==Construction== | ||
| Line 23: | Line 23: | ||
* x1 [[Uni-Ball Signo|Signo DX]] (grip) | * x1 [[Uni-Ball Signo|Signo DX]] (grip) | ||
====Additional | ====Additional items=== | ||
* Tape | * Tape | ||
| Line 30: | Line 30: | ||
# Cut both stripe section of the G2 grip from it's flat section. | # Cut both stripe section of the G2 grip from it's flat section. | ||
# Cut the front of both N900 body. | # Cut the front of both N900 body. | ||
# Cut 2x | # Cut 2x 2 mm and 1x 1.4 cm of Signo DX grip. | ||
# Cut both G-2506 grip to 2x | # Cut both G-2506 grip to 2x 2 mm and 2x 4 cm. | ||
# Cut 2 2. | # Cut 2 2.5 mm ring off N900 cap. | ||
# Cut the Sander barrel to 3. | # Cut the Sander barrel to 3.5 cm | ||
====Assembly==== | ====Assembly==== | ||
# | # Place the Opt tip inside the 700N cap. | ||
# | # Place the G2 stripe section over the 700N cap basis and Opt tip. | ||
# | # Place the 700N cap in the N900 barrel. | ||
# Add in this order: | # Add in this order: 2 mm of Signo DX grip, 2.5 mm of N900 cap and 4 cm of G-2506 grip on the N900 body (it should cover the tip structure). | ||
# Repeat on the other side. | # Repeat on the other side. | ||
# | # Place the Signo DX and G-2506 grip on the Sander body and connect. | ||
==References== | ==References== | ||
<references /> | |||
[[Category:Pen Mods]] | [[Category:Pen Mods]] | ||
Latest revision as of 17:29, 3 October 2026
The 台制戰彈 is a double-sided mod made by TWPS spinner Joey. The name can be roughly translated as "Taiwan-made Warheads".
Construction
Parts needed
List from Joey's post in the TWPS penmodding group on Facebook:
- x2 雄獅 NO.900水性美工筆 (body)
- x2 700N (caps)
- x2 Pilot Opt Shaker (tip)
- x2 SKB G-2506 (grip)
- x1 Sander B-1700 (barrel)
- x2 Pilot G2 (grip)
- x1 Signo DX (grip)
=Additional items
- Tape
Text tutorial
Preparation
- Cut both stripe section of the G2 grip from it's flat section.
- Cut the front of both N900 body.
- Cut 2x 2 mm and 1x 1.4 cm of Signo DX grip.
- Cut both G-2506 grip to 2x 2 mm and 2x 4 cm.
- Cut 2 2.5 mm ring off N900 cap.
- Cut the Sander barrel to 3.5 cm
Assembly
- Place the Opt tip inside the 700N cap.
- Place the G2 stripe section over the 700N cap basis and Opt tip.
- Place the 700N cap in the N900 barrel.
- Add in this order: 2 mm of Signo DX grip, 2.5 mm of N900 cap and 4 cm of G-2506 grip on the N900 body (it should cover the tip structure).
- Repeat on the other side.
- Place the Signo DX and G-2506 grip on the Sander body and connect.