Beige g3: Difference between revisions

← Older edit

Latest revision as of 18:18, 1 October 2026

The Beige G3 is a personal mod made by JEB spinner Beige.

Construction

Parts needed

List from Beige's blog:^[1]

1x Plastic G3 (barrel, tip, grip)
1x Zebra Hyper Jell (grip, cap)
1x HGG (tip, Grip)
1x Uni-Ball Signo (tip, grip)
1x New Sakura Ballsign (cap)
2x Pilot Supergrip（Grips）
1x Pilot CHOOSE（Plastic tip)
1x Pilot Hi-Tec-C（Tip）

Additional Items

Tape
An insert

Text tutorial

Preparation

Remove the Hyper Jell cap clip and sand the cut edge if necessary.
Remove the backplug, tip, grip and ink tube from the plastic G3. Sand down the nubs at the front.
Cut a 3–4 mm section from the smooth part of the G3 grip.
Cut SuperGrip sections of three, four and two rings, plus a second three-ring section for the Ballsign cap.
Cut a 5 mm section of HGG grip.

Assembly

Insert a three-ring SuperGrip section into the front of the G3 barrel.
Fit the small G3 grip section over the front, followed by the four-ring SuperGrip section.
Stack the tips with the plastic CHOOSE tip underneath, the HGG tip over it and the Signo tip outermost. Secure the stack with tape.
Place the tip stack inside the Hyper Jell grip and fit the grip onto the front.

Insert the two-ring SuperGrip section into the Hyper Jell cap, followed by the Hi-Tec-C tip.
Remove the Ballsign cap clip. Insert the remaining three-ring SuperGrip section into that cap, then insert the Ballsign cap into the Hyper Jell cap.
Add an optional insert to the barrel.
Fit the 5 mm HGG grip section over the rear of the G3 barrel, then attach the Hyper Jell cap.

References

↑ tutorial from Beige's blog

[1] tutorial from Beige's blog

[1]

@@ Line 13: / Line 13: @@
 ===Parts needed===
-List from Penmodding Wiki's article:<ref name="Beige's blog">http://beige72.blog.fc2.com/blog-entry-54.html</ref>
+List from Beige's blog:<ref>[http://beige72.blog.fc2.com/blog-entry-54.html tutorial from Beige's blog]</ref>
-* 1x [[Pilot G3|Plastic G3]] (Barrel, tip)
+* 1x [[Pilot G3|Plastic G3]] (barrel, tip, grip)
-* 1x [[Zebra Hyper Jell]] (Grip)
+* 1x [[Zebra Hyper Jell]] (grip, cap)
 * 1x [[Hybrid Gel Grip|HGG]] (tip, Grip)
 * 1x [[Uni-Ball Signo]] (tip, grip)
-* 1x [[Sakura Ballsign]] (New cap)
+* 1x New [[Sakura Ballsign]] (cap)
 * 2x [[Pilot Supergrip]]（Grips）
 * 1x [[Pilot CHOOSE]]（Plastic tip)
-* 1x [[Pilot Hi-Tec C]]（Tip）
+* 1x [[Pilot Hi-Tec-C]]（Tip）
 ====Additional Items====
 * Tape
 * An insert
 ===Text tutorial===
-====Mise en place====
+====Preparation====
-# Cut the clip of your [[Zebra Jimnie]] cap, sand if necessary
+# Remove the Hyper Jell cap clip and sand the cut edge if necessary.
-# Remove the backplug, tip, grip and ink of the [[Pilot G3|Plastic G3]], then sand down the nubs on the front
+# Remove the backplug, tip, grip and ink tube from the plastic G3. Sand down the nubs at the front.
-# Cut 3-4mm of the smooth part of G3 grip
+# Cut a 3–4 mm section from the smooth part of the G3 grip.
-# Cut 3 blocks, 4 blocks and 2 blocks of [[Pilot Supergrip]] grips
+# Cut SuperGrip sections of three, four and two rings, plus a second three-ring section for the Ballsign cap.
-# Cut 5mm of the HGG grip
+# Cut a 5 mm section of HGG grip.
 ====Assembly====
 <br>[[File:Beige1.jpg|left|thumb|200px]]<br clear=all>
-# Put 3 blocks of [[Pilot Supergrip]] inside the front of the G3 barrel
+# Insert a three-ring SuperGrip section into the front of the G3 barrel.
-# Add the small segment of g3 grip then 4 stripes on supergrip on the front
+# Fit the small G3 grip section over the front, followed by the four-ring SuperGrip section.
-# Tip stack these tips in these order: Signo < HGG < Pilot choose (pilot chose is under), add tape so it's stable
+# Stack the tips with the plastic CHOOSE tip underneath, the HGG tip over it and the Signo tip outermost. Secure the stack with tape.
-# Put the tipstack in the hyperjell grip and add the hyperjell grip on the front.
+# Place the tip stack inside the Hyper Jell grip and fit the grip onto the front.
 <br>[[File:Beige2.jpg|left|thumb|200px]]<br clear=all>
-# Put the [[Pilot Hi-Tec C]] tip inside the Hyperjell cap then push 2 blocks of [[Pilot Supergrip]].
+# Insert the two-ring SuperGrip section into the Hyper Jell cap, followed by the Hi-Tec-C tip.
-# Add 3 blocks of Supergrip in the Ballsign cap, then put it inside the Hyperjell cap
+# Remove the Ballsign cap clip. Insert the remaining three-ring SuperGrip section into that cap, then insert the Ballsign cap into the Hyper Jell cap.
-# (facultative add an insert)
+# Add an optional insert to the barrel.
-# Add the 0.5cm long hgg on the back on the g3 body, then connect it to the hyperjell cap
+# Fit the 5 mm HGG grip section over the rear of the G3 barrel, then attach the Hyper Jell cap.
 ==References==