Dark Mod Zero

The Dark Mod Zero is a personal mod made by spinner Orctupus Orctupus YouTube.

Construction

Parts needed

Source: Directly Published here by Orctupus

• 2x 9/32 - 5/16th Screw-in Target Point (Tip)
• 2x Pentel Energel Kuro (Body)
• 2x Pilot G2 (Grip)
• 2x TUL Ballpoint Retractable (Grip)
• 3x Dong-a Anyball (Grip)
• 1x Papermate Officemate (Barrel)

Additional Items

• Painters Tape | Paper Tape
• Utility Knife
• OPTIONAL: Pipe-Cutter
• Scissor End | Thin Metal Rod (To push the Energel Kuro Clicker housing out of the body)

Text tutorial

1. 1 Disassemble the Pentel Energel Kuro pens by unscrewing the tips (Set aside), removing the metal ring, ink-tube, breaking the clip, and popping out the back of the retractable clicker mechanism through the lower square hole leaving only the bodies.

1. 2 Measure and cut the Pentel Energel Kuro bodies 1cm from the back of the pen (clicker mechanism side) using a utility knife or pipe-cutter. Once both body's are cut, set aside.

1. 3 Disassemble the Papermate Officemate removing the front plug and ink-tube leaving only the barrel.

1. 4 Measure and cut the Papermate Officemate barrel 3.2cm from the front of the pen (Set aside).

1. 6 Disassemble the TUL Ballpoint Retractable pens removing the front tip, metal ring, ink-tube, and set aside the Grips.

1. 7 Disassemble the Pilot G2 pens removing only the grips and set aside

1. 8 Cut 2x 8-Sections of Grip from two of the Dong-a Anyball grips. Set aside.

1. 9 Cut 2x 4-Sections of Grip from one of the Dong-a Anyball grip. Set aside

1. 10 Stretch the Pilot G2 Grips using a pliers. Set aside.

1. 11 Wrap 2x the 9/32 - 5/16th Screw-in Target Point tips with Painters Tape or Paper Tape around the base until they can be placed snug into the Pentel Energel Kuro front barrel (threaded side).

1. 12 Place the Pentel Energel Kuro tips loosely over the 9/32 - 5/16th Screw-in Target Point tips and then push the TUL Ballpoint Retractable grip over both the tips and onto the barrel. (there will be a slight bump on the inner 1/3rd of the TUL grip.)

1. 13 Stretch the Pilot G2 Grip up and over the TUL Ballpoint Retractable Grip with the G2 rings facing outwards till the Pentel Energel Kuro tip is only seen about 2-3mm and there is 2-3mm of the TUL grip showing on the other side.

1. 14 Place the 2x 8-Sections of Dong-a Anyball grips on the other side of each Pentel Energel Kuro barrel. You want to have a flat section facing inwards vs the smooth thinner end on the inside. Slide it up against the Pilot G2 Grip.

1. 15 Place the 2x 4-Sections of Dong-a Anyball grips on the ring side of the Pilot G2 grip on each side.

1. 16 Use the Papermate Officemate 3.2cm cut body section to join the Pentel Energel Kuro Barrels and then put both sides together press-fit over the officemate section.

1. 17 FINISHED

Assembly

!!! IN PROGRESS !!!

Video Tutorial

!!! COMING SOON !!!

References

]