Toggle search
Toggle menu
481
1K
204
5.6K
Fen Spinner Wiki
Toggle preferences menu
Toggle personal menu
Not logged in
Your IP address will be publicly visible if you make any edits.

Venus Gospel (Ennis Emboss): Difference between revisions

From Fen Spinner Wiki
More actions
← Older edit
V 0 1 D (talk | contribs)
Administrators
3,077 edits
No edit summary
Validate text tutorial against recovered source; clarify construction and add heading reference and sourced images
 
Line 25: Line 25:
* Tape
* Tape


===Text tutorial===
===Text tutorial<ref>[https://penmodding.pm/archives/6710 Venus Gospel (Ennis Emboss) tutorial]</ref>===
====Preparation====
# Disassemble both Fabrico or compatible Tsukineko markers, removing the backplugs, caps, ink and felt tips. Cut off the narrow front noses.<br>[[File:VenusGospelEnnisEmbossTutorial01.jpg|left|thumb|200px]]<br clear=all>
# Disasemble both [[Tsukineko Fabrico]] marker
# Cut a 1 cm ring from a large Color Twin cap and file its interior until it fits snugly over the connector barrel.<br>[[File:VenusGospelEnnisEmbossTutorial02.jpg|left|thumb|200px]]<br clear=all><br>[[File:VenusGospelEnnisEmbossTutorial03.jpg|left|thumb|200px]]<br clear=all><br>[[File:VenusGospelEnnisEmbossTutorial04.jpg|left|thumb|200px]]<br clear=all>
# Cut 1cm of the big cap of [[Pentel Color Twin]], file the interior
# Cut a 4–5 cm Color Twin barrel connector. The source usually finds 4 cm sufficient; choose the end that fits the particular marker rear openings.<br>[[File:VenusGospelEnnisEmbossTutorial05.jpg|left|thumb|200px]]<br clear=all>
# Cut 4~5cm from your [[Pentel Color Twin]] barrel.
# Fit the cap ring around the connector’s centre and join the two marker rear openings with it.<br>[[File:VenusGospelEnnisEmbossTutorial06.jpg|left|thumb|200px]]<br clear=all>
# Dissasemble both Dr. Grip G-Spec MP and cut 2/3rd of the metal tubes (~3.33cm)
# Disassemble both Dr. Grip G-Spec mechanical pencils and retain two matching metal-tube sections. Ennis specifies approximately two-thirds of the tube, about 3.33 cm; the reproduced photos use approximately 3.5 cm.<br>[[File:VenusGospelEnnisEmbossTutorial07.jpg|left|thumb|200px]]<br clear=all>
# Cut 2.4cm of the Dr. Grip G-Spec MP grip from the front (the part with the inner lip), then separate the remaining grip in half (so you have one 2.4cm, and 2x 1.2cm of g-spec grip). the middle part won't be used
# Remove both Airfit mechanical-pencil lead sleeves. Tape each until it fits snugly inside a retained metal tube.
# Cut your [[Pilot SuperGrip]] grips at 2 stripes from the flat part
# Insert each metal-tube assembly into a Marvy backplug, lead-sleeve end first. Add tape for a secure fit.<br>[[File:VenusGospelEnnisEmbossTutorial08.jpg|left|thumb|200px]]<br clear=all><br>[[File:VenusGospelEnnisEmbossTutorial09.jpg|left|thumb|200px]]<br clear=all>
# Cut 2x2 stripes of [[Dong-A Anyball]] grips
# From each G-Spec grip, retain the front half and rear quarter. The photographed 4.8 cm grips provide 2.4 cm fronts and 1.2 cm rear sections; discard the middle quarters.<br>[[File:VenusGospelEnnisEmbossTutorial10.jpg|left|thumb|200px]]<br clear=all>
 
# Retain the smooth part and two stripes of each SuperGrip grip. Prepare two 2-stripe Anyball sections.<br>[[File:VenusGospelEnnisEmbossTutorial11.jpg|left|thumb|200px]]<br clear=all>
====Assembly====
# At each marker’s cut front, fit a Tect-2-Way ring and the G-Spec rear-quarter grip. Insert the prepared Marvy backplug weight assembly, then fit two Anyball stripes around the backplug.<br>[[File:VenusGospelEnnisEmbossTutorial12.jpg|left|thumb|200px]]<br clear=all><br>[[File:VenusGospelEnnisEmbossTutorial13.jpg|left|thumb|200px]]<br clear=all>
 
# Fit the prepared SuperGrip section over this assembly, stripes toward the outer end. Adjust it so the Marvy backplug end remains slightly exposed.<br>[[File:VenusGospelEnnisEmbossTutorial14.jpg|left|thumb|200px]]<br clear=all>
# Put the 1cm of big [[Pentel Color Twin]] cap on the 4~5cm section of it.
# Overgrip with the G-Spec front-half section. Repeat at the other end.<br>[[File:VenusGospelEnnisEmbossTutorial15.jpg|left|thumb|200px]]<br clear=all><br>[[File:VenusGospelEnnisEmbossTutorial16.jpg|left|thumb|200px]]<br clear=all>
# Add some tape around the lead sleve of [[Zebra Airfit BA-9|airfit]] and put it into the cutted G-Spec MP metal tube, it should fit snugly.
# Put the metal tube inside the [[Marvy Art Director 1300/1400]] backplugs.
# Add the [[Marvy Art Director 1300/1400]] backplugs inside the front side of [[Tsukineko Fabrico]] marker, add 2 stripes of [[Dong-A Anyball]] on top
# On [[Tsukineko Fabrico]], add the grips in this order: 1 o-ring of [[Zebra Tect-2-Way]], the 1.2cm of G-Spec MP (from the back pf the grip) then [[Pilot SuperGrip]] grip (2 stripes first).
# Overgrip the [[Pilot SuperGrip]] grip with the 2.4cm section of G-Spec MP grip.
# Repeat on the other side then connect on the [[Pentel Color Twin]] 4~5cm body.


===Video tutorial===
===Video tutorial===
Line 52: Line 46:


==References==
==References==
<references />


[[Category:Pen Mods]]
[[Category:Pen Mods]]

Latest revision as of 21:56, 2 October 2026

The Venus Gospel is a double-sided mod made by JEB spinner Ennis. It is also commonly called "Ennis Emboss".

Construction

Parts needed

List from Ennis's blog:[1]

Additional Items

  • Tape

Text tutorial[2]

  1. Disassemble both Fabrico or compatible Tsukineko markers, removing the backplugs, caps, ink and felt tips. Cut off the narrow front noses.

  2. Cut a 1 cm ring from a large Color Twin cap and file its interior until it fits snugly over the connector barrel.





  3. Cut a 4–5 cm Color Twin barrel connector. The source usually finds 4 cm sufficient; choose the end that fits the particular marker rear openings.

  4. Fit the cap ring around the connector’s centre and join the two marker rear openings with it.

  5. Disassemble both Dr. Grip G-Spec mechanical pencils and retain two matching metal-tube sections. Ennis specifies approximately two-thirds of the tube, about 3.33 cm; the reproduced photos use approximately 3.5 cm.

  6. Remove both Airfit mechanical-pencil lead sleeves. Tape each until it fits snugly inside a retained metal tube.
  7. Insert each metal-tube assembly into a Marvy backplug, lead-sleeve end first. Add tape for a secure fit.



  8. From each G-Spec grip, retain the front half and rear quarter. The photographed 4.8 cm grips provide 2.4 cm fronts and 1.2 cm rear sections; discard the middle quarters.

  9. Retain the smooth part and two stripes of each SuperGrip grip. Prepare two 2-stripe Anyball sections.

  10. At each marker’s cut front, fit a Tect-2-Way ring and the G-Spec rear-quarter grip. Insert the prepared Marvy backplug weight assembly, then fit two Anyball stripes around the backplug.



  11. Fit the prepared SuperGrip section over this assembly, stripes toward the outer end. Adjust it so the Marvy backplug end remains slightly exposed.

  12. Overgrip with the G-Spec front-half section. Repeat at the other end.



Video tutorial

Video tutorial by VoreTex.


References

  1. ↑ http://ennispin.blog.fc2.com/blog-entry-9.html
  2. ↑ Venus Gospel (Ennis Emboss) tutorial
Retrieved from "https://wiki.fenspinner.net/index.php?title=Venus_Gospel_(Ennis_Emboss)&oldid=5433"
Last modified
This page was last edited on 2 October 2026, at 21:56.