MeowSTA: Difference between revisions
From Fen Spinner Wiki
More actions
Cumlover2008 (talk | contribs) No edit summary |
No edit summary |
||
| Line 11: | Line 11: | ||
MeowSTA intends to be a heavy mod for slow spinning which is slightly thinner than Emboss. | MeowSTA intends to be a heavy mod for slow spinning which is slightly thinner than Emboss. | ||
Xeran changed the name from | Xeran changed the name from Fengear to MeowSTA on 10/02/2020. | ||
==Construction== | ==Construction== | ||
| Line 31: | Line 31: | ||
===Text Tutorial=== | ===Text Tutorial=== | ||
# Empty and clean STA barrel | # Empty and clean the STA barrel | ||
# Take backplugs off the Tulip markers and remove the nibs | # Take backplugs off the Tulip markers and remove the nibs | ||
# Cut 1cm from the lip of the small Emboss caps | # Cut 1cm from the lip of the small Emboss caps | ||
| Line 39: | Line 39: | ||
# Cut 1cm from the back of the Airblancs | # Cut 1cm from the back of the Airblancs | ||
# Hollow the CT caps | # Hollow the CT caps | ||
# Push one of the cut Supergrip sections into the CT cap, cut side in | # Push one of the cut Supergrip sections into the CT cap, cut side facing in | ||
# Put an inverted Signo tip into the Supergrip grip, the tip should sit flush with the grip <br>[[File:Meowsta_step10.jpg|left|thumb|200px]]<br clear=all> | # Put an inverted Signo tip into the Supergrip grip, the tip should sit flush with the grip <br>[[File:Meowsta_step10.jpg|left|thumb|200px]]<br clear=all> | ||
# Put inverted Opt tip | # Put inverted Opt tip into the Signo tip | ||
# Push one of the short Emboss cap section over the Opt tip, cut side out | # Push one of the short Emboss cap section over the Opt tip, cut side facing out | ||
# Put a G2 ring into the small Emboss cap <br>[[File:Meowsta_step13.jpg|left|thumb|200px]]<br clear=all> | # Put a G2 ring into the small Emboss cap <br>[[File:Meowsta_step13.jpg|left|thumb|200px]]<br clear=all> | ||
# Put front half of DGG onto the Emboss and CT cap | # Put a front half of DGG onto the Emboss and CT cap. Small cap and g2 section should be flush with the inside of the DGG | ||
# Put Airblanc section onto front of Tulip backplug | # Put Airblanc section onto front of Tulip backplug | ||
# Push Tulip backplug into CT cap | # Push Tulip backplug into CT cap | ||
Revision as of 01:29, 11 February 2021
The MeowSTA is an inverted mod made by Xeran as of 27/08/2020.
History
MeowSTA intends to be a heavy mod for slow spinning which is slightly thinner than Emboss.
Xeran changed the name from Fengear to MeowSTA on 10/02/2020.
Construction
Parts needed
- 2x Emboss (Two small caps)
- 2x Pilot Opt Shaker (Two tips)
- 2x Uni-ball Signo (Two tips)
- 2x Pilot Dr. Grip Shaker (Two grips)
- 2x Pentel ColorTwin (Two caps)
- 2x Pilot Supergrip (Two grips)
- 1x Pilot G2 (Grip)
- 2x Pilot Airblanc (Two grips)
- 1x STA Aquarelle (Barrel)
- 2x Tulip Dual-Tip (Two backplugs)
Other Materials
- Masking Tape
Text Tutorial
- Empty and clean the STA barrel
- Take backplugs off the Tulip markers and remove the nibs
- Cut 1cm from the lip of the small Emboss caps
- Cut DGGs in half
- Cut 2 separate rings from the middle of the ridged section of the G2 grip
- Cut 3 sections from the front of the Supergrips
- Cut 1cm from the back of the Airblancs
- Hollow the CT caps
- Push one of the cut Supergrip sections into the CT cap, cut side facing in
- Put an inverted Signo tip into the Supergrip grip, the tip should sit flush with the grip
- Put inverted Opt tip into the Signo tip
- Push one of the short Emboss cap section over the Opt tip, cut side facing out
- Put a G2 ring into the small Emboss cap
- Put a front half of DGG onto the Emboss and CT cap. Small cap and g2 section should be flush with the inside of the DGG
- Put Airblanc section onto front of Tulip backplug
- Push Tulip backplug into CT cap
- Wrap tape onto back of the Tulip backplug until it can fit snugly into the STA barrel
- Repeat steps 9-17 for the other cap
- Push assemblies onto STA barrel
- Complete
