MeowSTA: Difference between revisions
From Fen Spinner Wiki
More actions
Cumlover2008 (talk | contribs) No edit summary |
Cumlover2008 (talk | contribs) No edit summary |
||
| Line 21: | Line 21: | ||
* 2x [[Pentel ColorTwin]] (Two caps) | * 2x [[Pentel ColorTwin]] (Two caps) | ||
* 2x [[Pilot SuperGrip]] (Two grips) | * 2x [[Pilot SuperGrip]] (Two grips) | ||
* 1x [[Pilot | * 1x [[Pilot G2]] (Grip) | ||
* 2x [[Pilot AirBlanc]] (Two grips) | * 2x [[Pilot AirBlanc]] (Two grips) | ||
* 1x [[STA Aquarelle]] (Barrel) | * 1x [[STA Aquarelle]] (Barrel) | ||
| Line 35: | Line 35: | ||
# Cut 1cm from the lip of the small Emboss caps | # Cut 1cm from the lip of the small Emboss caps | ||
# Cut DGGs in half | # Cut DGGs in half | ||
# Cut 2 separate rings from the middle of the ridged section of the | # Cut 2 separate rings from the middle of the ridged section of the G2 grip | ||
# Cut 3 sections from the front of the Supergrips | # Cut 3 sections from the front of the Supergrips | ||
# Cut 1cm from the back of the Airblancs | # Cut 1cm from the back of the Airblancs | ||
| Line 43: | Line 43: | ||
# Put inverted Opt tip onto the Signo tip | # Put inverted Opt tip onto the Signo tip | ||
# Push one of the short Emboss cap section over the Opt tip, cut side out | # Push one of the short Emboss cap section over the Opt tip, cut side out | ||
# Put a | # Put a G2 ring into the small Emboss cap <br>[[File:Meowsta_step13.jpg|left|thumb|200px]]<br clear=all> | ||
# Put front half of DGG onto the Emboss and CT cap, small cap and g2 section should be flush with the inside of the DGG | # Put front half of DGG onto the Emboss and CT cap, small cap and g2 section should be flush with the inside of the DGG | ||
# Put AirBlanc section onto front of Tulip backplug | # Put AirBlanc section onto front of Tulip backplug | ||
Revision as of 00:23, 11 February 2021
The MeowSTA is an inverted mod made by Xeran as of 27/08/2020.
History
MeowSTA intends to be a heavy mod for slow spinning which is slightly thinner than Emboss.
Xeran changed the name from FenSTA to MeowSTA on 10/02/2020.
Construction
Parts needed
- 2x Emboss (Two small caps)
- 2x Pilot Opt Shaker (Two tips)
- 2x Uni-ball Signo (Two tips)
- 2x Pilot Dr. Grip Shaker (Two grips)
- 2x Pentel ColorTwin (Two caps)
- 2x Pilot SuperGrip (Two grips)
- 1x Pilot G2 (Grip)
- 2x Pilot AirBlanc (Two grips)
- 1x STA Aquarelle (Barrel)
- 2x Tulip Dual-Tip (Two backplugs)
Other Materials
- Masking Tape
Text Tutorial
- Empty and clean STA barrel with acetone/nail polish remover
- Take backplugs off the Tulip markers and remove the nibs
- Cut 1cm from the lip of the small Emboss caps
- Cut DGGs in half
- Cut 2 separate rings from the middle of the ridged section of the G2 grip
- Cut 3 sections from the front of the Supergrips
- Cut 1cm from the back of the Airblancs
- Hollow the CT caps
- Push one of the cut Supergrip sections into the CT cap, cut side in
- Put an inverted Signo tip into the Supergrip grip, the tip should sit flush with the grip
- Put inverted Opt tip onto the Signo tip
- Push one of the short Emboss cap section over the Opt tip, cut side out
- Put a G2 ring into the small Emboss cap
- Put front half of DGG onto the Emboss and CT cap, small cap and g2 section should be flush with the inside of the DGG
- Put AirBlanc section onto front of Tulip backplug
- Push Tulip backplug into CT cap
- Wrap tape onto back of the Tulip backplug until it can fit snugly into the STA barrel
- Repeat steps 9-17 for the other cap
- Push assemblies onto STA barrel
- Complete
