Menowa* G3 (Old version): Difference between revisions
From Fen Spinner Wiki
More actions
Validate former Menowa G3 tutorial, correct tip donors, add sourced step photos and heading reference |
|||
| Line 14: | Line 14: | ||
===Parts needed=== | ===Parts needed=== | ||
Parts list from Penmodding.pm<ref name="Tutorial">https://penmodding.pm/archives/5947</ref>: | Parts list from Penmodding.pm<ref name="Tutorial">https://penmodding.pm/archives/5947</ref>: | ||
* 1x [[Pilot G3|G3]] (barrel and | * 1x [[Pilot G3|G3]] (barrel and cap) | ||
* 1x [[Zebra Hyperjell|Jimnie]] (cap | * 1x [[Zebra Hyperjell|Jimnie]] (cap) | ||
* 1x Zebra Airfit LT GEL/Ballpoint (tip) | * 1x Zebra Airfit LT GEL/Ballpoint (tip) | ||
* 1x [[Dong-A Anyball]] (grip) | * 1x [[Dong-A Anyball]] (grip) | ||
| Line 23: | Line 23: | ||
* 1x [[Pentel Color Twin]] (barrel) | * 1x [[Pentel Color Twin]] (barrel) | ||
* 1x [[Pilot G2]] (barrel) | * 1x [[Pilot G2]] (barrel) | ||
* 1x [[Pilot | * 1x [[Pilot G1]] (tip) | ||
* 1x [[Pentel Hybrid Gel Grip]] (tip) | * 1x [[Pentel Hybrid Gel Grip]] (tip; for the Airfit LT Gel stack) | ||
* 2x [[Zebra Airfit BA-9]] (metal rings) | * 2x [[Zebra Airfit BA-9]] (metal rings) | ||
| Line 31: | Line 31: | ||
* An insert (or multiple) | * An insert (or multiple) | ||
===Text tutorial=== | ===Text tutorial<ref name="Tutorial" />=== | ||
====Preparation==== | ====Preparation==== | ||
# Cut the clip of the G3 cap and remove the rubber stopper. | # Cut the clip of the G3 cap and remove the rubber stopper. | ||
# [[G3 Barrel Preparation|Prepare the G3 barrel]], then sand down the front until it's possible to fit an insert under the G2 barrel when connecting. | # [[G3 Barrel Preparation|Prepare the G3 barrel]], then sand down the front until it's possible to fit an insert under the G2 barrel when connecting. | ||
# Cut | # Cut the G2 barrel to 4.7 cm as shown in the source.<br>[[File:MenowaOldG3G2Cut.jpg|left|thumb|200px]]<br clear=all> | ||
# Shorten the Jimnie cap to 3.2 cm.<br>[[File:MenowaOldG3JimnieCut.jpg|left|thumb|200px]]<br clear=all> | |||
# | # Cut off and retain the top of the Namae backplug. | ||
# Cut the top | # Cut a 5 mm section from the middle of the Dr. Grip grip. | ||
# Cut | # Cut the large rear ring and a three-ring Anyball section for the front assembly, plus one-ring and two-ring sections for the cap. | ||
# Cut the | # Cut a 2.3 cm Color Twin barrel section. | ||
# Cut 2.3 cm | |||
====Assembly==== | ====Assembly==== | ||
=====Front side===== | =====Front side===== | ||
# | # Fit the G2 barrel onto the G3 front with its threaded end facing outwards.<br>[[File:MenowaOldG3FrontBarrel.jpg|left|thumb|200px]]<br clear=all> | ||
# Add the big ring of Anyball grip, an Airfit ring, the Jimnie cap (Optional: Put an insert underneath), then another airfit ring. | # Add the big ring of Anyball grip, an Airfit ring, the Jimnie cap (Optional: Put an insert underneath), then another airfit ring. | ||
# Stack the tips in this order if you use LT Ballpoint tip: Airfit LT bp tip, and G1 tip. The tip stack with LT Gel is: HGG tip, Airfit LT gel tip, and G1 tip. | # Stack the tips in this order if you use LT Ballpoint tip: Airfit LT bp tip, and G1 tip. The tip stack with LT Gel is: HGG tip, Airfit LT gel tip, and G1 tip.<br>[[File:MenowaOldG3BallpointStack.jpg|left|thumb|200px]]<br clear=all><br>[[File:MenowaOldG3GelStack.jpg|left|thumb|200px]]<br clear=all> | ||
# | # Place the tip stack in the g2 barrel (it should fit snugly) | ||
# Adjust the | # Fit the three-ring Anyball section at the front. Adjust the Jimnie cap for balance; the source shows 1 cm of the G2 threaded section exposed.<br>[[File:MenowaOldG3FrontAssembly.jpg|left|thumb|200px]]<br clear=all> | ||
=====Cap side===== | =====Cap side===== | ||
# | # Place the Muji aluminum tip inside the g3 cap.<br>[[File:MenowaOldG3MujiTip.jpg|left|thumb|200px]]<br clear=all> | ||
# | # Place the Namae backplug and the cut section of ct barrel inside the cap (Optional: Wrap an insert around the Ct barrel).<br>[[File:MenowaOldG3RearBarrel.jpg|left|thumb|200px]]<br clear=all> | ||
# On the cap | # On the cap, fit these grips from the barrel toward the outer end: one Anyball ring, 5 mm of Dr. Grip grip, then two Anyball rings.<br>[[File:MenowaOldG3RearGrips.jpg|left|thumb|200px]]<br clear=all> | ||
# Add tape on the G3 body then connect it to the G3 cap. | # Add tape on the G3 body then connect it to the G3 cap.<br>[[File:MenowaOldG3Finished.jpg|left|thumb|200px]]<br clear=all> | ||
==References== | ==References== | ||
Latest revision as of 19:36, 1 October 2026
The Menowa* G3 is a personal mod made by Menowa*. As he no longer uses it, its name could be translated as "Former G3" (旧G3).
Construction
Parts needed
Parts list from Penmodding.pm[1]:
- 1x G3 (barrel and cap)
- 1x Jimnie (cap)
- 1x Zebra Airfit LT GEL/Ballpoint (tip)
- 1x Dong-A Anyball (grip)
- 1x Pilot Dr. Grip (grip)
- 1x Namae (back plug)
- 1x Muji Aluminum Pen (tip)
- 1x Pentel Color Twin (barrel)
- 1x Pilot G2 (barrel)
- 1x Pilot G1 (tip)
- 1x Pentel Hybrid Gel Grip (tip; for the Airfit LT Gel stack)
- 2x Zebra Airfit BA-9 (metal rings)
Additional items
- Tape
- An insert (or multiple)
Text tutorial[1]
Preparation
- Cut the clip of the G3 cap and remove the rubber stopper.
- Prepare the G3 barrel, then sand down the front until it's possible to fit an insert under the G2 barrel when connecting.
- Cut the G2 barrel to 4.7 cm as shown in the source.
- Shorten the Jimnie cap to 3.2 cm.
- Cut off and retain the top of the Namae backplug.
- Cut a 5 mm section from the middle of the Dr. Grip grip.
- Cut the large rear ring and a three-ring Anyball section for the front assembly, plus one-ring and two-ring sections for the cap.
- Cut a 2.3 cm Color Twin barrel section.
Assembly
Front side
- Fit the G2 barrel onto the G3 front with its threaded end facing outwards.
- Add the big ring of Anyball grip, an Airfit ring, the Jimnie cap (Optional: Put an insert underneath), then another airfit ring.
- Stack the tips in this order if you use LT Ballpoint tip: Airfit LT bp tip, and G1 tip. The tip stack with LT Gel is: HGG tip, Airfit LT gel tip, and G1 tip.
- Place the tip stack in the g2 barrel (it should fit snugly)
- Fit the three-ring Anyball section at the front. Adjust the Jimnie cap for balance; the source shows 1 cm of the G2 threaded section exposed.
Cap side
- Place the Muji aluminum tip inside the g3 cap.
- Place the Namae backplug and the cut section of ct barrel inside the cap (Optional: Wrap an insert around the Ct barrel).
- On the cap, fit these grips from the barrel toward the outer end: one Anyball ring, 5 mm of Dr. Grip grip, then two Anyball rings.
- Add tape on the G3 body then connect it to the G3 cap.
