Dentoru Emboss: Difference between revisions
From Fen Spinner Wiki
More actions
m Copyedit: spelling and grammar |
Publish wording review of existing tutorial; retain construction without adding a source, per editor direction |
||
| Line 23: | Line 23: | ||
===Text tutorial=== | ===Text tutorial=== | ||
# Cut a 7-ring section from the back of two Anyball grips (4-'''7''') | # Cut a 7-ring section from the back of two Anyball grips (4-'''7''') | ||
# Cut a 4-ring section, two rings away from the front of two Anyball grips (2-'''4'''-5) | # Cut a 4-ring section, two rings away from the front of two Anyball grips (2-'''4'''-5) | ||
# Cut 4 rings from the G2 grips; keep the larger section. | # Cut 4 rings from the G2 grips; keep the larger section. | ||
# Cut | # Cut 3 cm of the Giotto barrels from the back end | ||
# Cut two | # Cut two 3 mm sections from your thin grip | ||
# Cut two | # Cut two 3 cm sections from the smooth part of the 2ballpen+sharpen grips | ||
# Clean and empty the Emboss. | # Clean and empty the Emboss. | ||
# | # Place the backplug back into the Emboss <br>[[File:Dentoru emboss1.jpg|250px|thumb|left]]<br clear=all> | ||
# Place a thin grip section on the front of a PC2 small cap <br>[[File:dentoru_emboss2.jpg|250px|thumb|left]]<br clear=all> | # Place a thin grip section on the front of a PC2 small cap <br>[[File:dentoru_emboss2.jpg|250px|thumb|left]]<br clear=all> | ||
# | # Place the G2 grip, cut-side first, onto the front of the PC2 cap leaving 1 cm of the cap exposed <br>[[File:dentoru_emboss3.jpg|250px|thumb|left]]<br clear=all> | ||
# Push 1-3 penzgear rings into the G2 grip <br>[[File:dentoru_emboss4.jpg|250px|thumb|left]]<br clear=all> | # Push 1-3 penzgear rings into the G2 grip <br>[[File:dentoru_emboss4.jpg|250px|thumb|left]]<br clear=all> | ||
# Place the package into the Giotto barrel from the back end <br>[[File:dentoru_emboss5.jpg|250px|thumb|left]]<br clear=all> | # Place the package into the Giotto barrel from the back end <br>[[File:dentoru_emboss5.jpg|250px|thumb|left]]<br clear=all> | ||
| Line 40: | Line 39: | ||
# Wrap tape around the Emboss front and backplug until the packages fit onto the ends snugly | # Wrap tape around the Emboss front and backplug until the packages fit onto the ends snugly | ||
# Push the packages onto the Emboss <br>[[File:dentoru_emboss7.jpg|250px|thumb|left]]<br clear=all> | # Push the packages onto the Emboss <br>[[File:dentoru_emboss7.jpg|250px|thumb|left]]<br clear=all> | ||
==References== | |||
<references /> | |||
[[Category:Pen Mods]] | [[Category:Pen Mods]] | ||
Latest revision as of 17:28, 3 October 2026
Dentoru Emboss is an adjustable mod made by Dentoru. It was created to emulate the look and feel of the Menowa* Reimei but on an Emboss body.
Construction
Parts needed
- 1x Emboss (Body, backplug)
- 2x Giotto Turbo Maxi (Two bodies)
- 2x 2ballpen+sharpen or can be substituted with Zebra Z-Grip (Two grips)
- 4x Anyball (Two grips)
- 2x Playcolor 2 (Two small caps)
- 2x Pilot G2 (Two grips)
- 1x Penzgear (2/4/6 Rings)
- 1x Pentel Hybrid Gel Grip or Pentel RSVP or similar (thin grip).
- Tape (Original uses cellophane tape)
Text tutorial
- Cut a 7-ring section from the back of two Anyball grips (4-7)
- Cut a 4-ring section, two rings away from the front of two Anyball grips (2-4-5)
- Cut 4 rings from the G2 grips; keep the larger section.
- Cut 3 cm of the Giotto barrels from the back end
- Cut two 3 mm sections from your thin grip
- Cut two 3 cm sections from the smooth part of the 2ballpen+sharpen grips
- Clean and empty the Emboss.
- Place the backplug back into the Emboss
- Place a thin grip section on the front of a PC2 small cap
- Place the G2 grip, cut-side first, onto the front of the PC2 cap leaving 1 cm of the cap exposed
- Push 1-3 penzgear rings into the G2 grip
- Place the package into the Giotto barrel from the back end
- Put 7 section Anyball, 4 section Anyball, and 2ballpen+sharpen section onto the package
- Repeat steps 9-13 to make a second assembly.
- Wrap tape around the Emboss front and backplug until the packages fit onto the ends snugly
- Push the packages onto the Emboss
