Dark Mod Zero: Difference between revisions
From Fen Spinner Wiki
More actions
| Line 29: | Line 29: | ||
===Text tutorial=== | ===Text tutorial=== | ||
# Disassemble the [[Pentel Energel Kuro]] pens by unscrewing the tips (Set aside), removing the metal ring, ink-tube, breaking the clip, and popping out the back of the retractable clicker mechanism through the lower square hole leaving only the bodies. | #1 Disassemble the [[Pentel Energel Kuro]] pens by unscrewing the tips (Set aside), removing the metal ring, ink-tube, breaking the clip, and popping out the back of the retractable clicker mechanism through the lower square hole leaving only the bodies. | ||
# Measure and cut the [[Pentel Energel Kuro]] bodies 1cm from the back of the pen (clicker mechanism side) using a utility knife or pipe-cutter. Once both body's are cut, set aside. | #2 Measure and cut the [[Pentel Energel Kuro]] bodies 1cm from the back of the pen (clicker mechanism side) using a utility knife or pipe-cutter. Once both body's are cut, set aside. | ||
# Disassemble the [[Papermate Officemate]] removing the front plug and ink-tube leaving only the barrel. | #3 Disassemble the [[Papermate Officemate]] removing the front plug and ink-tube leaving only the barrel. | ||
# Measure and cut the [[Papermate Officemate]] barrel 3.2cm from the front of the pen (Set aside). | #4 Measure and cut the [[Papermate Officemate]] barrel 3.2cm from the front of the pen (Set aside). | ||
# Disassemble the [[TUL Ballpoint Retractable]] pens removing the front tip, metal ring, ink-tube, and set aside the Grips. | #6 Disassemble the [[TUL Ballpoint Retractable]] pens removing the front tip, metal ring, ink-tube, and set aside the Grips. | ||
# Disassemble the [[Pilot G2]] pens removing only the grips and set aside | #7 Disassemble the [[Pilot G2]] pens removing only the grips and set aside | ||
# Cut 2x 8-Sections of Grip from two of the [[Papermate profile | Dong-a Anyball]] grips. Set aside. | #8 Cut 2x 8-Sections of Grip from two of the [[Papermate profile | Dong-a Anyball]] grips. Set aside. | ||
# Cut 2x 4-Sections of Grip from one of the [[Papermate profile | Dong-a Anyball]] grip. Set aside | #9 Cut 2x 4-Sections of Grip from one of the [[Papermate profile | Dong-a Anyball]] grip. Set aside | ||
# Stretch the [[Pilot G2]] Grips using a pliers. Set aside. | #10 Stretch the [[Pilot G2]] Grips using a pliers. Set aside. | ||
# Wrap 2x the [[9/32 - 5/16th Screw-in Target Point]] tips with Painters Tape or Paper Tape around the base until they can be placed snug into the [[Pentel Energel Kuro]] front barrel (threaded side). | #11 Wrap 2x the [[9/32 - 5/16th Screw-in Target Point]] tips with Painters Tape or Paper Tape around the base until they can be placed snug into the [[Pentel Energel Kuro]] front barrel (threaded side). | ||
# Place the [[Pentel Energel Kuro]] tips loosely over the [[9/32 - 5/16th Screw-in Target Point]] tips and then push the [[TUL Ballpoint Retractable]] grip over both the tips and onto the barrel. (there will be a slight bump on the inner 1/3rd of the TUL grip.) | #12 Place the [[Pentel Energel Kuro]] tips loosely over the [[9/32 - 5/16th Screw-in Target Point]] tips and then push the [[TUL Ballpoint Retractable]] grip over both the tips and onto the barrel. (there will be a slight bump on the inner 1/3rd of the TUL grip.) | ||
# Stretch the [[Pilot G2]] Grip up and over the [[TUL Ballpoint Retractable]] Grip with the G2 rings facing outwards till the [[Pentel Energel Kuro]] tip is only seen about 2-3mm and there is 2-3mm of the TUL grip showing on the other side. | #13 Stretch the [[Pilot G2]] Grip up and over the [[TUL Ballpoint Retractable]] Grip with the G2 rings facing outwards till the [[Pentel Energel Kuro]] tip is only seen about 2-3mm and there is 2-3mm of the TUL grip showing on the other side. | ||
# Place the 2x 8-Sections of [[Papermate profile | Dong-a Anyball]] grips on the other side of each [[Pentel Energel Kuro]] barrel. You want to have a flat section facing inwards vs the smooth thinner end on the inside. Slide it up against the [[Pilot G2]] Grip. | #14 Place the 2x 8-Sections of [[Papermate profile | Dong-a Anyball]] grips on the other side of each [[Pentel Energel Kuro]] barrel. You want to have a flat section facing inwards vs the smooth thinner end on the inside. Slide it up against the [[Pilot G2]] Grip. | ||
# Place the 2x 4-Sections of [[Papermate profile | Dong-a Anyball]] grips on the ring side of the [[Pilot G2]] grip on each side. | #15 Place the 2x 4-Sections of [[Papermate profile | Dong-a Anyball]] grips on the ring side of the [[Pilot G2]] grip on each side. | ||
# Use the [[Papermate Officemate]] 3.2cm cut body section to join the [[Pentel Energel Kuro]] Barrels and then put both sides together press-fit over the officemate section. | #16 Use the [[Papermate Officemate]] 3.2cm cut body section to join the [[Pentel Energel Kuro]] Barrels and then put both sides together press-fit over the officemate section. | ||
# FINISHED | #17 FINISHED | ||
====Assembly==== | ====Assembly==== | ||
Revision as of 00:36, 20 October 2024
The Dark Mod Zero is a personal mod made by spinner Orctupus Orctupus YouTube.
Construction
Parts needed
Source: Directly Published here by Orctupus
- 2x 9/32 - 5/16th Screw-in Target Point (Tip)
- 2x Pentel Energel Kuro (Body)
- 2x Pilot G2 (Grip)
- 2x TUL Ballpoint Retractable (Grip)
- 3x Dong-a Anyball (Grip)
- 1x Papermate Officemate (Barrel)
Additional Items
- Painters Tape | Paper Tape
- Utility Knife
- OPTIONAL: Pipe-Cutter
- Scissor End | Thin Metal Rod (To push the Energel Kuro Clicker housing out of the body)
Text tutorial
- 1 Disassemble the Pentel Energel Kuro pens by unscrewing the tips (Set aside), removing the metal ring, ink-tube, breaking the clip, and popping out the back of the retractable clicker mechanism through the lower square hole leaving only the bodies.
- 2 Measure and cut the Pentel Energel Kuro bodies 1cm from the back of the pen (clicker mechanism side) using a utility knife or pipe-cutter. Once both body's are cut, set aside.
- 3 Disassemble the Papermate Officemate removing the front plug and ink-tube leaving only the barrel.
- 4 Measure and cut the Papermate Officemate barrel 3.2cm from the front of the pen (Set aside).
- 6 Disassemble the TUL Ballpoint Retractable pens removing the front tip, metal ring, ink-tube, and set aside the Grips.
- 7 Disassemble the Pilot G2 pens removing only the grips and set aside
- 8 Cut 2x 8-Sections of Grip from two of the Dong-a Anyball grips. Set aside.
- 9 Cut 2x 4-Sections of Grip from one of the Dong-a Anyball grip. Set aside
- 10 Stretch the Pilot G2 Grips using a pliers. Set aside.
- 11 Wrap 2x the 9/32 - 5/16th Screw-in Target Point tips with Painters Tape or Paper Tape around the base until they can be placed snug into the Pentel Energel Kuro front barrel (threaded side).
- 12 Place the Pentel Energel Kuro tips loosely over the 9/32 - 5/16th Screw-in Target Point tips and then push the TUL Ballpoint Retractable grip over both the tips and onto the barrel. (there will be a slight bump on the inner 1/3rd of the TUL grip.)
- 13 Stretch the Pilot G2 Grip up and over the TUL Ballpoint Retractable Grip with the G2 rings facing outwards till the Pentel Energel Kuro tip is only seen about 2-3mm and there is 2-3mm of the TUL grip showing on the other side.
- 14 Place the 2x 8-Sections of Dong-a Anyball grips on the other side of each Pentel Energel Kuro barrel. You want to have a flat section facing inwards vs the smooth thinner end on the inside. Slide it up against the Pilot G2 Grip.
- 15 Place the 2x 4-Sections of Dong-a Anyball grips on the ring side of the Pilot G2 grip on each side.
- 16 Use the Papermate Officemate 3.2cm cut body section to join the Pentel Energel Kuro Barrels and then put both sides together press-fit over the officemate section.
- 17 FINISHED
Assembly
!!! IN PROGRESS !!!
Video Tutorial
!!! COMING SOON !!!
References
]