SVGiotto: Difference between revisions
From Fen Spinner Wiki
More actions
Publish wording review of existing tutorial; retain construction without adding a source, per editor direction |
|||
| (One intermediate revision by the same user not shown) | |||
| Line 8: | Line 8: | ||
|cog= cop | |cog= cop | ||
}} | }} | ||
The '''SVGiotto''' is a double sided mod made by [[FPSB]] spinner [[Ark0nix]]. This mod is his variation of the [[Ivan Giotto]] | The '''SVGiotto''' is a double-sided mod made by [[FPSB]] spinner [[Ark0nix]]. This mod is his variation of the [[Ivan Giotto]]. | ||
==Construction== | ==Construction== | ||
| Line 26: | Line 26: | ||
===Text tutorial=== | ===Text tutorial=== | ||
====Preparation==== | ====Preparation==== | ||
# Cut the front and | # Cut the front and Disassemble both Giotto barrels. | ||
# Cut the Giotto backplug from the ring | # Cut the Giotto backplug from the ring | ||
# Cut the transparent grip to 2x ~ | # Cut the transparent grip to 2x ~3 mm section. | ||
# Cut 1 of the 2 Giotto bodies in half. | # Cut 1 of the 2 Giotto bodies in half. | ||
# Cut the 2 Dr.Grip grips in half, the flat part will be used. | # Cut the 2 Dr.Grip grips in half, the flat part will be used. | ||
| Line 36: | Line 36: | ||
# Add one O-ring on each backplug, and connect the 2 halves of the cut Giotto barrel. (tape might be necessary to hold the parts well) | # Add one O-ring on each backplug, and connect the 2 halves of the cut Giotto barrel. (tape might be necessary to hold the parts well) | ||
# On the Giotto barrel, add in this order: an O-ring, the transparent section and a DGG half. | # On the Giotto barrel, add in this order: an O-ring, the transparent section and a DGG half. | ||
# | # Place the Technica-X tip inside the DGG grip. | ||
# Repeat on the other side. | # Repeat on the other side. | ||
| Line 44: | Line 44: | ||
==References== | ==References== | ||
<references /> | |||
[[Category:Pen Mods]] | [[Category:Pen Mods]] | ||
Latest revision as of 17:30, 3 October 2026
The SVGiotto is a double-sided mod made by FPSB spinner Ark0nix. This mod is his variation of the Ivan Giotto.
Construction
Parts needed
- x2 Giotto Turbo Maxi (2 body and backplug)
- x2 Pilot Dr. Grip (2 grip)
- It is possible to use only one
- x2 Pentel Technica-X (2 tips)
- x4 O-ring
- x1 transparent grip
Additional Items
- Tape
Text tutorial
Preparation
- Cut the front and Disassemble both Giotto barrels.
- Cut the Giotto backplug from the ring
- Cut the transparent grip to 2x ~3 mm section.
- Cut 1 of the 2 Giotto bodies in half.
- Cut the 2 Dr.Grip grips in half, the flat part will be used.
Assembly
- Put one giotto backplug in each hole of the uncuted Giotto body.
- Add one O-ring on each backplug, and connect the 2 halves of the cut Giotto barrel. (tape might be necessary to hold the parts well)
- On the Giotto barrel, add in this order: an O-ring, the transparent section and a DGG half.
- Place the Technica-X tip inside the DGG grip.
- Repeat on the other side.
Trivia
• This mod was named in a meeting of 2025 after the rapper "SVG", formally Arkhor in FPSB