Menowa* Prize Mod: Difference between revisions
From Fen Spinner Wiki
More actions
mNo edit summary |
Clarify sourced Prize Mod tip and grip assemblies, cap fitting and optional foil tape; add images |
||
| (2 intermediate revisions by 2 users not shown) | |||
| Line 8: | Line 8: | ||
|cog= cop | |cog= cop | ||
}} | }} | ||
The '''Menowa Prize Mod''' is a | The '''Menowa Prize Mod''' is a double-sided KT-type mod made by [[UPSB]] modder Lost ANGELUS. This mod was made for [[Menowa*]] as his prize for winning [[Pen Spinning World Tournament 2015]]. | ||
==Construction== | ==Construction== | ||
| Line 14: | Line 14: | ||
List from the video below: | List from the video below: | ||
* x1 Tulip Chisel Tip Marker ( | * x1 Tulip Chisel Tip Marker (body) | ||
* x2 [[Pentel RSVP]] ( | * x2 [[Pentel RSVP]] (grips) | ||
* x1 [[Sailor IC Liquid Gel]] (grip) | * x1 [[Sailor IC Liquid Gel]] (grip) | ||
* x2 [[TUL Mechanical Pencil]] ( | * x2 [[TUL Mechanical Pencil]] (tips) | ||
* x2 [[Pilot Dr. Grip]] (Grips) | * x2 [[Pilot Dr. Grip]] (Grips) | ||
* x2 [[Pentel Color Twin]] ( | * x2 [[Pentel Color Twin]] (big caps) | ||
* x2 O-ring | * x2 O-ring | ||
====Additional | ====Additional items==== | ||
* Foil tape | * Foil tape (optional) | ||
* Tape and sandpaper for fitting the caps | |||
===Text tutorial=== | ===Text tutorial<ref>[https://penmodding.pm/archives/5574 Menowa* Prize Mod tutorial]</ref>=== | ||
====Preparation==== | ====Preparation==== | ||
# Cut | # Cut a 1.5 cm section from the smooth, non-lip end of each Dr. Grip grip.<br>[[File:MenowaPrizeDrGripCut.jpg|left|thumb|200px]]<br clear=all> | ||
# Cut | # Cut two 4 mm RSVP sections.<br>[[File:MenowaPrizeRSVPCuts.jpg|left|thumb|200px]]<br clear=all> | ||
# Cut | # Cut two two-ring and two three-ring Sailor sections.<br>[[File:MenowaPrizeSailorCuts.jpg|left|thumb|200px]]<br clear=all> | ||
# Hollow | # Hollow out both large Color Twin caps. | ||
# | # Remove the Tulip marker’s writing tip and barrel printing.<br>[[File:MenowaPrizeBarrel.jpg|left|thumb|200px]]<br clear=all> | ||
====Assembly==== | ====Assembly==== | ||
# | # Remove the lead-holding mechanisms from both TUL mechanical-pencil tips. Insert a tip backwards into each hollowed cap.<br>[[File:MenowaPrizeTULTip.jpg|left|thumb|200px]]<br clear=all><br>[[File:MenowaPrizeTipInsertion.jpg|left|thumb|200px]]<br clear=all> | ||
# | # Place one O-ring inside the outer end of each cap, around the TUL tip.<br>[[File:MenowaPrizeORing.jpg|left|thumb|200px]]<br clear=all> | ||
# | # Fit a two-ring Sailor section onto one cap, followed by a 1.5 cm Dr. Grip section.<br>[[File:MenowaPrizeCapGrips.jpg|left|thumb|200px]]<br clear=all> | ||
# | # Fit a three-ring Sailor section inside the Dr. Grip section, then insert a 4 mm RSVP section into the Sailor section.<br>[[File:MenowaPrizeCapAssembly.jpg|left|thumb|200px]]<br clear=all> | ||
# | # Repeat the grip assembly on the second cap.<br>[[File:MenowaPrizeBothCaps.jpg|left|thumb|200px]]<br clear=all> | ||
# | # Fit both caps onto the Tulip barrel. Sand the rear of the barrel if its cap is too tight, and add tape at the front if needed for a secure fit. | ||
# | # Optionally cut four 6–7 mm-wide foil-tape strips. Place them under the two-ring Sailor sections and under the cap joints on the Tulip barrel.<br>[[File:MenowaPrizeFinished.jpg|left|thumb|200px]]<br clear=all> | ||
===Video tutorial=== | ===Video tutorial=== | ||
| Line 48: | Line 49: | ||
==References== | ==References== | ||
<references /> | |||
[[Category:Pen Mods]] | [[Category:Pen Mods]] | ||
Latest revision as of 19:37, 1 October 2026
The Menowa Prize Mod is a double-sided KT-type mod made by UPSB modder Lost ANGELUS. This mod was made for Menowa* as his prize for winning Pen Spinning World Tournament 2015.
Construction
Parts needed
List from the video below:
- x1 Tulip Chisel Tip Marker (body)
- x2 Pentel RSVP (grips)
- x1 Sailor IC Liquid Gel (grip)
- x2 TUL Mechanical Pencil (tips)
- x2 Pilot Dr. Grip (Grips)
- x2 Pentel Color Twin (big caps)
- x2 O-ring
Additional items
- Foil tape (optional)
- Tape and sandpaper for fitting the caps
Text tutorial[1]
Preparation
- Cut a 1.5 cm section from the smooth, non-lip end of each Dr. Grip grip.
- Cut two 4 mm RSVP sections.
- Cut two two-ring and two three-ring Sailor sections.
- Hollow out both large Color Twin caps.
- Remove the Tulip marker’s writing tip and barrel printing.
Assembly
- Remove the lead-holding mechanisms from both TUL mechanical-pencil tips. Insert a tip backwards into each hollowed cap.
- Place one O-ring inside the outer end of each cap, around the TUL tip.
- Fit a two-ring Sailor section onto one cap, followed by a 1.5 cm Dr. Grip section.
- Fit a three-ring Sailor section inside the Dr. Grip section, then insert a 4 mm RSVP section into the Sailor section.
- Repeat the grip assembly on the second cap.
- Fit both caps onto the Tulip barrel. Sand the rear of the barrel if its cap is too tight, and add tape at the front if needed for a secure fit.
- Optionally cut four 6–7 mm-wide foil-tape strips. Place them under the two-ring Sailor sections and under the cap joints on the Tulip barrel.
Video tutorial
Video tutorial by Lost ANGELUS.