NIKoo G3: Difference between revisions
From Fen Spinner Wiki
More actions
mNo edit summary |
mNo edit summary |
||
| (One intermediate revision by the same user not shown) | |||
| Line 8: | Line 8: | ||
|cog= | |cog= | ||
}} | }} | ||
The '''NIKoo G3''' is a single sided mod made by [[JEB]] spinner [[NIKoo]]. This mod is a variation of the [[GJH]] mod. As | The '''NIKoo G3''' is a single sided mod made by [[JEB]] spinner [[NIKoo]]. This mod is a variation of the [[GJH]] mod. As NIKoo never released it's tutorial, the mod presented here is a replica. | ||
==Construction== | ==Construction== | ||
| Line 14: | Line 14: | ||
===Parts needed=== | ===Parts needed=== | ||
List from the UPSB V3<ref name="Tutorial">https://web.archive.org/web/20121101115016/http://www.upsb.info/forum/index.php?showtopic=21320</ref>: | List from the UPSB V3<ref name="Tutorial">https://web.archive.org/web/20121101115016/http://www.upsb.info/forum/index.php?showtopic=21320</ref>: | ||
* 1x [[Pilot G3|G3]] (Metalic tip, barrel, | * 1x [[Pilot G3|G3]] (Metalic tip, barrel, and cap) | ||
* 1x Jedo (tip) | * 1x Jedo (tip) | ||
* 3x [[Pentel Hybrid Gel Grip|HGG]] (3 tips and 2 grip) | * 3x [[Pentel Hybrid Gel Grip|HGG]] (3 tips and 2 grip) | ||
| Line 29: | Line 29: | ||
====Preparation==== | ====Preparation==== | ||
# Cut your Airblanc grip to approximately 1.2cm and 1.8cm. | # Cut your Airblanc grip to approximately 1.2cm and 1.8cm. | ||
# Cut a small section and the ring of one HGG grip. | # Cut a small section and the ring of one HGG grip. | ||
Latest revision as of 22:12, 2 February 2025
The NIKoo G3 is a single sided mod made by JEB spinner NIKoo. This mod is a variation of the GJH mod. As NIKoo never released it's tutorial, the mod presented here is a replica.
Construction
Parts needed
List from the UPSB V3[1]:
- 1x G3 (Metalic tip, barrel, and cap)
- 1x Jedo (tip)
- 3x HGG (3 tips and 2 grip)
- 1x Dong-A Anyball (grip)
- 1x Grip G-Spec MP (outer and inner grip)
- 1x Pilot AirBlanc (grip)
Additional Items
- Tape
- An insert
- Glue
Text tutorial
Preparation
- Cut your Airblanc grip to approximately 1.2cm and 1.8cm.
- Cut a small section and the ring of one HGG grip.
- Cut your G-spec grip to slightly longer than the previous step
- Cut 2x 2 blocks of Anyball grip.
- File the bump of the g3 barrel.
- Cut the thread part of the g3 front (including its bump).
Assembly
Front side
- Add 2 blocks of anyball grip and the HGG grip at the front of the G3.
- Stack the tips in this order inside the HGG grip: G3 tip onto Jedo tip, and Jedo tip onto Hgg tip.
- Overgrip the HGG grip with: the bigger cut section of Airblanc grip, 2 blocks of Anyball grip and the smaller cut section of Airblanc grip.
Cap side
- Put the signo tip, g-spec inner grip, HGG ring (in this order) inside the G3 cap.
- Put the HGG small part onto the G3 cap, overgrip it with the cut outer grip of G-spec
- Add some tape on the end of the G3 barrel, then connect the G3 cap to it.