VGG Emboss: Difference between revisions
From Fen Spinner Wiki
More actions
No edit summary |
Resolve source review; correct construction and cite tutorial heading |
||
| Line 8: | Line 8: | ||
|cog= cop | |cog= cop | ||
}} | }} | ||
The '''VGG Emboss''' is a double-sided mod made by [[VicGotGame]]. | The '''VGG Emboss''' is a double-sided mod made by [[VicGotGame]]. The construction below documents Cloud’s replica; it does not establish VicGotGame’s original construction. | ||
==Construction== | ==Construction== | ||
| Line 17: | Line 17: | ||
* x2 [[Zebra Airfit BA-9]] (tips) | * x2 [[Zebra Airfit BA-9]] (tips) | ||
* x2 [[Dong-A Computer Sign Pen]] (body) | * x2 [[Dong-A Computer Sign Pen]] (body) | ||
* | * x1 [[Sailor IC Liquid Gel]] (grip) | ||
* x1 Beifa (black grip) | |||
====Additional Items==== | ====Additional Items==== | ||
* hot glue | * hot glue | ||
===Text tutorial= | ===Text tutorial<ref>[https://web.archive.org/web/20131102175937/http://forum.upsb.info/showthread.php?t=7052 Cloud’s VGG Emboss replica tutorial]</ref>=== | ||
This tutorial describes '''Cloud's VGG Emboss replica'''. Cloud explicitly states that VicGotGame did not approve the reconstruction and that it may differ from the original. | |||
# Cut two 4-section Beifa grip pieces, two 2-ring Sailor pieces, and two 2 cm Dr. Grip sections.<br>[[File:VGGEmbossReplicaGrips.jpg|left|thumb|200px]]<br clear=all> | |||
# Cut | # Remove the Emboss ink and nibs, clean the barrel, and replace its backplug. | ||
# | # Cut each small Emboss cap to retain 1 cm from the end that fits over the backplug. Smooth the cuts.<br>[[File:VGGEmbossReplicaSmallCapCut.jpg|left|thumb|200px]]<br clear=all> | ||
# Cut | # Cut two 1.5 cm sections from the rear of the Comssa barrels.<br>[[File:VGGEmbossReplicaComssaCut.jpg|left|thumb|200px]]<br clear=all> | ||
# Cut | # Fit a Sailor section over each end of the Emboss barrel. Fit the uncut end of a Comssa section over that end, then use the barrel end to push the section fully into a large Emboss cap until the cap meets the Sailor grip. | ||
# Fit a Dr. Grip section to each large cap, followed by a Beifa section, then insert an Airfit tip at the outer end.<br>[[File:VGGEmbossReplicaCapWeights.jpg|left|thumb|200px]]<br clear=all> | |||
# Use hot glue at the joint shown in Cloud's tutorial to connect the Comssa section, small Emboss cap, and inside of the large cap.<br>[[File:VGGEmbossReplicaGlueJoint.jpg|left|thumb|200px]]<br clear=all> | |||
# Repeat the end assembly and attach both ends to the barrel.<br>[[File:VGGEmbossReplicaFinished.jpg|left|thumb|200px]]<br clear=all> | |||
# | |||
# | |||
# | |||
# Repeat | |||
==References== | ==References== | ||
<references /> | |||
[[Category:Pen Mods]] | [[Category:Pen Mods]] | ||
Latest revision as of 16:07, 3 October 2026
The VGG Emboss is a double-sided mod made by VicGotGame. The construction below documents Cloud’s replica; it does not establish VicGotGame’s original construction.
Construction
Parts needed
List from UPSB V4 [1]
- x2 Tsukineko Emboss (1 body, 2 big cap, 2 small cap, and 1 backplug)
- x2 Pilot Dr. Grip (Grip)
- x2 Zebra Airfit BA-9 (tips)
- x2 Dong-A Computer Sign Pen (body)
- x1 Sailor IC Liquid Gel (grip)
- x1 Beifa (black grip)
Additional Items
- hot glue
Text tutorial[2]
This tutorial describes Cloud's VGG Emboss replica. Cloud explicitly states that VicGotGame did not approve the reconstruction and that it may differ from the original.
- Cut two 4-section Beifa grip pieces, two 2-ring Sailor pieces, and two 2 cm Dr. Grip sections.
- Remove the Emboss ink and nibs, clean the barrel, and replace its backplug.
- Cut each small Emboss cap to retain 1 cm from the end that fits over the backplug. Smooth the cuts.
- Cut two 1.5 cm sections from the rear of the Comssa barrels.
- Fit a Sailor section over each end of the Emboss barrel. Fit the uncut end of a Comssa section over that end, then use the barrel end to push the section fully into a large Emboss cap until the cap meets the Sailor grip.
- Fit a Dr. Grip section to each large cap, followed by a Beifa section, then insert an Airfit tip at the outer end.
- Use hot glue at the joint shown in Cloud's tutorial to connect the Comssa section, small Emboss cap, and inside of the large cap.
- Repeat the end assembly and attach both ends to the barrel.
