MX^2: Difference between revisions
From Fen Spinner Wiki
More actions
m →Text tutorial: Removed excessive redirect |
|||
| Line 25: | Line 25: | ||
====Preparation==== | ====Preparation==== | ||
# Cut a ring at the end of every grips (except 1 HGG grip). | # Cut a ring at the end of every grips (except 1 HGG grip). | ||
# File the rounded part at the front of the | # File the rounded part at the front of the RSVP body. | ||
# Glue 4 section of grip to each other | # Glue 4 section of grip to each other | ||
# Cut a remaining | # Cut a remaining RSVP grip in half | ||
# Cut the clip of the | # Cut the clip of the RSVP cap | ||
# Do a hole in the | # Do a hole in the RSVP backplug | ||
====Assembly==== | ====Assembly==== | ||
# Wrap 7 cm of tape around the front of the | # Wrap 7 cm of tape around the front of the RSVP barrel | ||
# Put some teflon on the tip of | # Put some teflon on the tip of RSVP body. | ||
# Put the ring of the RSVP and the ring of the HGG on the front of the | # Put the ring of the RSVP and the ring of the HGG on the front of the RSVP body. | ||
# Put 2 | # Put 2 HGG tip on the front of the front of the RSVP body (add some teflon tape to secure it) | ||
# Wrap again some tape around the | # Wrap again some tape around the RSVP front (to also cover the HGG tip) | ||
# Put one | # Put one HGG grip on the front. | ||
# Put the | # Put the HGG grip inside the cap | ||
# Put the glued rings inside the | # Put the glued rings inside the RSVP cap | ||
# Inside the ring and the | # Inside the ring and the HGG, put the half of RSVP grip between both. | ||
# Put | # Put RSVP inktube inside the backplug, add the cap onto it | ||
==References== | ==References== | ||
Revision as of 21:06, 11 December 2024
The MX^2 is a single sided mod made by TeK.
Construction
Parts needed
List from FPSB V2:[1]
- 2x Pentel RSVP body (1 Barrel, 1 Cap, 2 Grips, 1 Backcap)
- 2x Pentel Hybrid Gel Grip (2 Tips, 2 Grips)
Additional Items
- Tape + Teflon tape
Text tutorial
Preparation
- Cut a ring at the end of every grips (except 1 HGG grip).
- File the rounded part at the front of the RSVP body.
- Glue 4 section of grip to each other
- Cut a remaining RSVP grip in half
- Cut the clip of the RSVP cap
- Do a hole in the RSVP backplug
Assembly
- Wrap 7 cm of tape around the front of the RSVP barrel
- Put some teflon on the tip of RSVP body.
- Put the ring of the RSVP and the ring of the HGG on the front of the RSVP body.
- Put 2 HGG tip on the front of the front of the RSVP body (add some teflon tape to secure it)
- Wrap again some tape around the RSVP front (to also cover the HGG tip)
- Put one HGG grip on the front.
- Put the HGG grip inside the cap
- Put the glued rings inside the RSVP cap
- Inside the ring and the HGG, put the half of RSVP grip between both.
- Put RSVP inktube inside the backplug, add the cap onto it