Everchix Emboss: Difference between revisions
From Fen Spinner Wiki
More actions
m Copyedit: correct measurement |
Correct the 3 cm centre connector, donor parts and older grip measurement; restore barrel emptying and add four sourced diagrams. |
||
| Line 15: | Line 15: | ||
List from Pm.pm:<ref name="Tutorial">https://penmodding.pm/archives/5452</ref> | List from Pm.pm:<ref name="Tutorial">https://penmodding.pm/archives/5452</ref> | ||
* x2 [[Tsukineko Emboss Dual Pen|Tsukineko Emboss]] (body) | * x2 [[Tsukineko Emboss Dual Pen|Tsukineko Emboss]] (body) | ||
* | * x1 [[Pilot SuperGrip]]/[[Zebra Hyper Jell]] (grip) | ||
* x2 [[Zebra Airfit BA-9]] (Tips) | * x2 [[Zebra Airfit BA-9]] (Tips) | ||
* x2 [[Sailor IC Liquid Gel]] (grips) | * x2 [[Sailor IC Liquid Gel]] (grips) | ||
* x1 [[Pentel Color Twin]] (barrel) | * x1 [[Pentel Color Twin]] (barrel) | ||
* x1 [[Dong-A Computer Sign Pen]] ( | * x1 [[Dong-A Computer Sign Pen]] (barrel) | ||
===Text tutorial=== | ===Text tutorial=== | ||
====Preparation==== | ====Preparation==== | ||
# | # Empty both Emboss barrels.<br>[[File:EverchixEmbossEmptyBarrels.jpg|left|thumb|200px]]<br clear=all> | ||
# Cut | # Working from the rear of each Emboss barrel, cut a 5.7 cm section, followed by a 3.1 cm section. Discard the remaining nib-end section.<br>[[File:EverchixEmbossBarrelCuts.jpg|left|thumb|200px]]<br clear=all> | ||
# Cut | # Cut two 2 cm sections of Comssa barrel. | ||
# Cut | # Cut a 3 cm section from the front of a Color Twin barrel. | ||
# Cut three two-ring sections of SuperGrip grip. The older construction uses approximately 3.5 mm Hyper Jell sections instead, as shown in the joint diagram. | |||
====Assembly==== | ====Assembly==== | ||
# Centre a grip section over each Comssa connector and the Color Twin connector. | |||
# | # Join a 3.1 cm Emboss section to a 5.7 cm section using a 2 cm Comssa connector. Repeat for the other pair.<br>[[File:EverchixEmbossConnector.jpg|left|thumb|200px]]<br clear=all> | ||
# | # Join the two 5.7 cm Emboss sections with the 3 cm Color Twin connector. The grip sections cover the three joints.<br>[[File:EverchixEmbossJointGrips.jpg|left|thumb|200px]]<br clear=all> | ||
# | # Fit an Airfit tip onto each outer 3.1 cm Emboss section and secure it with a Sailor grip. | ||
===Video tutorial=== | ===Video tutorial=== | ||
| Line 42: | Line 42: | ||
==References== | ==References== | ||
<references /> | |||
[[Category:Pen Mods]] | [[Category:Pen Mods]] | ||
Latest revision as of 18:40, 1 October 2026
The Everchix Emboss is a double sided mod made by JEB spinner Everchix.
Construction
Parts needed
List from Pm.pm:[1]
- x2 Tsukineko Emboss (body)
- x1 Pilot SuperGrip/Zebra Hyper Jell (grip)
- x2 Zebra Airfit BA-9 (Tips)
- x2 Sailor IC Liquid Gel (grips)
- x1 Pentel Color Twin (barrel)
- x1 Dong-A Computer Sign Pen (barrel)
Text tutorial
Preparation
- Empty both Emboss barrels.
- Working from the rear of each Emboss barrel, cut a 5.7 cm section, followed by a 3.1 cm section. Discard the remaining nib-end section.
- Cut two 2 cm sections of Comssa barrel.
- Cut a 3 cm section from the front of a Color Twin barrel.
- Cut three two-ring sections of SuperGrip grip. The older construction uses approximately 3.5 mm Hyper Jell sections instead, as shown in the joint diagram.
Assembly
- Centre a grip section over each Comssa connector and the Color Twin connector.
- Join a 3.1 cm Emboss section to a 5.7 cm section using a 2 cm Comssa connector. Repeat for the other pair.
- Join the two 5.7 cm Emboss sections with the 3 cm Color Twin connector. The grip sections cover the three joints.
- Fit an Airfit tip onto each outer 3.1 cm Emboss section and secure it with a Sailor grip.
Video tutorial
Video tutorial by Oleg.