Laluteskal Ballsign: Difference between revisions
From Fen Spinner Wiki
More actions
| (One intermediate revision by the same user not shown) | |||
| Line 20: | Line 20: | ||
* 2x [[Tombow Playcolor2]] (clipless caps) | * 2x [[Tombow Playcolor2]] (clipless caps) | ||
* 2x [[Pilot AirBlanc]] (grip) | * 2x [[Pilot AirBlanc]] (grip) | ||
* | * 2x [[Ohto Needle Point]] (tips) | ||
* | * 1x [[Penzgear]] (two rings) | ||
===Additional items=== | ===Additional items=== | ||
| Line 28: | Line 28: | ||
===Text tutorial=== | ===Text tutorial=== | ||
====Preparation==== | ====Preparation==== | ||
# | # Empty the Ballsign barrel and add an insert if desired. | ||
# | # Separate the smooth and ribbed sections of all four SuperGrip grips. Keep the ribbed sections. | ||
# Cut two small | # Cut two small Dr. Grip sections for the outer overgrips. | ||
# Cut | # Cut two Airblanc sections, each approximately the length of four SuperGrip rings. | ||
====Assembly==== | ====Assembly<ref>[https://penmodding.pm/archives/5428 Laluteskal Ballsign tutorial]</ref>==== | ||
# | # Fit one ribbed SuperGrip section onto the inner half of a Playcolor2 cap, leaving room for the outer grip assembly. Cover it with an Airblanc section.<br>[[File:LaluteskalBallsignInnerGrips.jpg|left|thumb|200px]]<br clear=all> | ||
# Insert a Needle Point tip and one Pen’z Gear ring into another ribbed SuperGrip section.<br>[[File:LaluteskalBallsignTipAndRing.jpg|left|thumb|200px]]<br clear=all> | |||
# Cover this outer section with a small Dr. Grip section, then fit it onto the outer end of the cap.<br>[[File:LaluteskalBallsignDrGrip.jpg|left|thumb|200px]]<br clear=all> | |||
# | # Repeat the assembly on the second Playcolor2 cap. | ||
# | # Fit both prepared caps onto the Ballsign barrel. | ||
# Repeat on the | |||
==References== | ==References== | ||
<references /> | |||
[[Category:Pen Mods]] | [[Category:Pen Mods]] | ||
Latest revision as of 19:30, 1 October 2026
The Laluteskal Ballsign is a double-sided mod made by JEB spinner Laluteskal.
Construction
Parts needed
Parts list from Ponkotu's blog[1]
- 1x Sakura Ballsign (1 body)
- 4x Pilot SuperGrip (4 grips)
- 2x Pilot Dr. Grip (grip)
- 2x Tombow Playcolor2 (clipless caps)
- 2x Pilot AirBlanc (grip)
- 2x Ohto Needle Point (tips)
- 1x Penzgear (two rings)
Additional items
- An insert
Text tutorial
Preparation
- Empty the Ballsign barrel and add an insert if desired.
- Separate the smooth and ribbed sections of all four SuperGrip grips. Keep the ribbed sections.
- Cut two small Dr. Grip sections for the outer overgrips.
- Cut two Airblanc sections, each approximately the length of four SuperGrip rings.
Assembly[2]
- Fit one ribbed SuperGrip section onto the inner half of a Playcolor2 cap, leaving room for the outer grip assembly. Cover it with an Airblanc section.
- Insert a Needle Point tip and one Pen’z Gear ring into another ribbed SuperGrip section.
- Cover this outer section with a small Dr. Grip section, then fit it onto the outer end of the cap.
- Repeat the assembly on the second Playcolor2 cap.
- Fit both prepared caps onto the Ballsign barrel.
