KAtts Acrylic Bullet Mod: Difference between revisions

Latest revision as of 11:12, 28 August 2026

The kAtts Acrylic Bullet mod is a double-sided mod made by kAtts which he used in his Pen Spinning World Tournament 2019 participation.

Contrary to what its name implies, the mod does not use an acrylic tube for the barrel. It uses a polycarbonate tube.

Construction

Parts needed

Parts list from the video below:

x1 Polycarbonate tube (13 mm OD, 11 mm ID)
x2 Pilot Dr. Grip (grip)
x1 Pilot AirBlanc (grip)
x2 Nato bullet 7.62×51 mm
x~6 Dong-A Anyball (Grip) (2 colored ones)
x1 Zebra Hyper Jell (Grip)

=Additional items

An insert

Text tutorial

Preparation

Cut your Dr. Grip grips into two ~1.5 cm-long sections.
Cut two 8-block pieces of Anyball grip, six 1-block pieces (including two colored ones), four 3-block pieces, and four 2-block pieces (including two colored ones).
Cut your Polycarbonate tube to 20 cm.
Cut your AirBlanc grip to two 1 cm sections.
Cut your Hyper Jell to ~9–10 mm.

Assembly

Put the grips in this order: one stripe of Anyball grip, then a colored one, then ~1.5 cm of Dr. Grip grip then one block of Anyball on the polycarbonate barrel, leave some space to prepare the rest of the gripping.
Put on the polycarbonate barrel 8-block of Anyball grip and fold it on itself from the exterior side.
Put 1 cm of AirBlanc grip inside the polycarbonate barrel and put the Nato bullet tip inside it, the AirBlanc grip should block it. ~10 mm of it should remain visible.
Put ~10 mm of Hyper Jell grip, then overgrip it with 3 blocks of Anyball grip.
Unfold the 8 blocks of Anyball grip over the tip part, and adjust.
Overgrip the 8 blocks of Anyball grip in this order: 2 blocks of Anyball, 2 blocks of Anyball (colored) then 3 blocks of Anyball.
(Optional) Add an insert.
Repeat on the other side.

Video tutorial

Video tutorial by kAtts.

References

@@ Line 8: / Line 8: @@
 |cog= cop
 }}
-The '''kAtts Acrylic Bullet mod''' is a double sided mod made by [[kAtts]] which he used in his [[Pen Spinning World Tournament 2019]] participation.
+The '''kAtts Acrylic Bullet mod''' is a double-sided mod made by [[kAtts]] which he used in his [[Pen Spinning World Tournament 2019]] participation.
-Countrary to what it name implies, the mod does not use Acrylic. It uses polycarbonate.
+Contrary to what its name implies, the mod does not use an acrylic tube for the barrel. It uses a polycarbonate tube.
 ==Construction==
@@ Line 16: / Line 16: @@
 ===Parts needed===
-List from the video below
+Parts list from the video below:
-* x1 Polycarbonate tube (13mm od, 11mm id)
+* x1 Polycarbonate tube (13 mm OD, 11 mm ID)
 * x2 [[Pilot Dr. Grip]] (grip)
-* x1 [[Pilot AirBlanc]] (Grip)
+* x1 [[Pilot AirBlanc]] (grip)
-* x2 Nato bullet 7,62X51mm
+* x2 Nato bullet 7.62×51 mm
-* x~6 [[Dong-A Anyball]] (Grip) (2 colored one)
+* x~6 [[Dong-A Anyball]] (Grip) (2 colored ones)
 * x1 [[Zebra Hyper Jell]] (Grip)
-====Additional Items====
+====Additional items===
 * An insert
 ===Text tutorial===
 ====Preparation====
-# Cut your [[Pilot Dr. Grip]] grips in 2 ~1.5cm long section.
+# Cut your Dr. Grip grips into two ~1.5 cm-long sections.
-# Cut 2x 8 block of [[Dong-A Anyball]] grip, 6x 1 block (including 2 colored one), 4x 3 block and 4x 2 block (including 2 colored one).
+# Cut two 8-block pieces of Anyball grip, six 1-block pieces (including two colored ones), four 3-block pieces, and four 2-block pieces (including two colored ones).
-# Cut your Polycarbonate tube to 20cm.
+# Cut your Polycarbonate tube to 20 cm.
-# Cut your [[Pilot AirBlanc]] grip to 2x 1cm section.
+# Cut your AirBlanc grip to two 1 cm sections.
-# Cut your [[Zebra Hyper Jell]] to ~9/10 mm.
+# Cut your Hyper Jell to ~9–10 mm.
 ====Assembly====
-# Put the grips in this order: one stripe of [[Dong-A Anyball]] grip, then a colored one, then ~1.5cm of [[Pilot Dr. Grip]] grip then one block of anyball on the polycarbonate barrel, leave some space to prepare the rest of the gripping.
+# Put the grips in this order: one stripe of Anyball grip, then a colored one, then ~1.5 cm of Dr. Grip grip then one block of Anyball on the polycarbonate barrel, leave some space to prepare the rest of the gripping.
-# put on the polycarbonate barrel 8 block of [[Dong-A Anyball]] grip and fold it on itself from the exterior side.
+# Put on the polycarbonate barrel 8-block of Anyball grip and fold it on itself from the exterior side.
-# Put 1cm of [[Pilot AirBlanc]] grip inside the polycarbonate barrel and put the Nato bullet tip inside it, the airblanc grip should block it. ~10 mm of it should remain visible.
+# Put 1 cm of AirBlanc grip inside the polycarbonate barrel and put the Nato bullet tip inside it, the AirBlanc grip should block it. ~10 mm of it should remain visible.
-# Put ~10mm of [[Zebra Hyper Jell]] grip, then overgrip it with 3 block of [[Dong-A Anyball]].
+# Put ~10 mm of Hyper Jell grip, then overgrip it with 3 blocks of Anyball grip.
-# Unfold the 8 block of [[Dong-A Anyball]] grip over the tip part, adjust.
+# Unfold the 8 blocks of Anyball grip over the tip part, and adjust.
-# Overgrip the 8 block of [[Dong-A Anyball]] grip in this order: 2 block of [[Dong-A Anyball]], 2 block of [[Dong-A Anyball]] (colored) then 3 block of [[Dong-A Anyball]].
+# Overgrip the 8 blocks of Anyball grip in this order: 2 blocks of Anyball, 2 blocks of Anyball (colored) then 3 blocks of Anyball.
-# (facultative) Add an insert.
+# (Optional) Add an insert.
-# Repeat on the other side
+# Repeat on the other side.
 ===Video tutorial===
 <youtube>https://www.youtube.com/watch?v=T0xKFGXpooE</youtube>