I.suk Fountain Mod: Difference between revisions
From Fen Spinner Wiki
More actions
m →Text tutorial: Removed excessive redirect |
Resolve tutorial review; retain wiki measurements where external sources omit them |
||
| (One intermediate revision by the same user not shown) | |||
| Line 8: | Line 8: | ||
|cog= cop | |cog= cop | ||
}} | }} | ||
The '''I.suk Fountain Mod''' is a double sided mod made by [[i.suk]]. | The '''I.suk Fountain Mod''' is a double-sided mod made by [[i.suk]]. | ||
==Construction== | ==Construction== | ||
| Line 14: | Line 14: | ||
===Parts needed=== | ===Parts needed=== | ||
Parts list from the video below: | |||
* x2 [[Crayola SuperTips]] (2 | * x2 [[Crayola SuperTips]] (2 bodies) | ||
* x1/2 [[Dong-A Anyball]]（1 Grip (2 for the colored version)) | * x1/2 [[Dong-A Anyball]]（1 Grip (2 for the colored version)) | ||
* x2 [[Pilot Dr. Grip]] (grip) | * x2 [[Pilot Dr. Grip]] (grip) | ||
* x2 [[Zebra Airfit BA-9|Zebra Airfit]] (tips) | * x2 [[Zebra Airfit BA-9|Zebra Airfit]] (tips) | ||
* x2 Pentel fountain pen Jm20Wu ( | * x2 Pentel fountain pen Jm20Wu (caps) | ||
* x1 [[Pentel RSVP]] (Grip) | * x1 [[Pentel RSVP]] (Grip) | ||
* x1 pencil | * x1 pencil | ||
===Text tutorial=== | ===Text tutorial<ref>[https://www.youtube.com/watch?v=ubvTly4T63M I.suk Fountain Mod construction tutorial].</ref>=== | ||
# Remove the clips | # Remove the clips from two Pentel JM20 fountain-pen caps and cut each cap to 42 mm. | ||
# Cut | # Cut both Dr. Grip grips in half and retain the halves with the lip. | ||
# Cut | # Cut two 2-block and two 1-block Anyball sections. | ||
# | # Fit an Airfit Jell tip to the outer end of each cap and secure it with a Dr. Grip grip section. Fit one 2-block and one 1-block Anyball section at each inner cap end. | ||
# Cut | # Cut two SuperTips barrel sections to 78 mm. | ||
# Cut | # Cut a pencil connector to approximately 3.14 cm. Fit an RSVP grip ring at its centre and wrap tape around the connector as needed. | ||
# Join the SuperTips sections with the pencil connector. | |||
# | # Fit a prepared cap to each end and adjust the insertion depth until approximately 63 mm of SuperTips barrel is exposed on each side of the centre. | ||
# | |||
===Video tutorial=== | ===Video tutorial=== | ||
| Line 42: | Line 41: | ||
==References== | ==References== | ||
<references /> | |||
[[Category:Pen Mods]] | [[Category:Pen Mods]] | ||
Latest revision as of 20:43, 3 October 2026
The I.suk Fountain Mod is a double-sided mod made by i.suk.
Construction
Parts needed
Parts list from the video below:
- x2 Crayola SuperTips (2 bodies)
- x1/2 Dong-A Anyball（1 Grip (2 for the colored version))
- x2 Pilot Dr. Grip (grip)
- x2 Zebra Airfit (tips)
- x2 Pentel fountain pen Jm20Wu (caps)
- x1 Pentel RSVP (Grip)
- x1 pencil
Text tutorial[1]
- Remove the clips from two Pentel JM20 fountain-pen caps and cut each cap to 42 mm.
- Cut both Dr. Grip grips in half and retain the halves with the lip.
- Cut two 2-block and two 1-block Anyball sections.
- Fit an Airfit Jell tip to the outer end of each cap and secure it with a Dr. Grip grip section. Fit one 2-block and one 1-block Anyball section at each inner cap end.
- Cut two SuperTips barrel sections to 78 mm.
- Cut a pencil connector to approximately 3.14 cm. Fit an RSVP grip ring at its centre and wrap tape around the connector as needed.
- Join the SuperTips sections with the pencil connector.
- Fit a prepared cap to each end and adjust the insertion depth until approximately 63 mm of SuperTips barrel is exposed on each side of the centre.
Video tutorial
Video tutorial by i.suk.