GioGear: Difference between revisions
From Fen Spinner Wiki
More actions
Created page with "{{Mod Infobox |name= |image={{#setmainimage:GioGear.png}} |creator= Magiai |style= Double Sided |length= 27.1cm |weight= 19g |cog= cop }} The '''Giotto X''' is a double sided mod made by GPC seller Spinworld. ==Construction== ===Parts needed=== List from Magiai's blog:<ref>[https://magiaiarchive.blogspot.com/2024/12/giogear-tutorial.html tutorial from Magiai's blog]</ref> * 2x Giotto Turbo Maxi (Everything except ink and backplugs) * 1x Small plastic tube **..." |
Resolve source review; correct construction and cite tutorial heading |
||
| (2 intermediate revisions by 2 users not shown) | |||
| Line 8: | Line 8: | ||
|cog= cop | |cog= cop | ||
}} | }} | ||
The ''' | The '''GioGear''' is a [[Titan Gear]] type mod invented by [[Magiai]] as the cheapest possible variation of the Titan Gear. | ||
==Construction== | ==Construction== | ||
| Line 16: | Line 16: | ||
* 1x Small plastic tube | * 1x Small plastic tube | ||
** The non-stretched one used in the tutorial can fit inside a Flexgrip | ** The non-stretched one used in the tutorial can fit inside a Flexgrip | ||
* 1x | * 1x SuperTips-diameter barrel section (approximately 4 cm; centre connector) | ||
===Text tutorial<ref>[https://penmodding.pm/archives/7858 GioGear tutorial], photographs by Magiai.</ref>=== | |||
===Text tutorial | # Empty both Giotto Turbo Maxi barrels. Cut and retain 7 mm from the front of each barrel.<br>[[File:GioGearFrontCut.jpg|left|thumb|200px]]<br clear=all> | ||
# Scrape out the obstruction inside both retained front sections, as shown by the before-and-after photograph.<br>[[File:GioGearFrontHollowing.jpg|left|thumb|200px]]<br clear=all> | |||
# Cut | # Separate each cap’s inner part from its outer shell. Retain 3 cm of the cap’s flat outer section and cut 8 mm from the flat end of the inner part.<br>[[File:GioGearCapCuts.jpg|left|thumb|200px]]<br clear=all> | ||
# | # Fit the flat inner-cap section over the narrow end of the retained Giotto front section. Fit the remaining inner-cap piece inside its wider opening.<br>[[File:GioGearNestedParts.jpg|left|thumb|200px]]<br clear=all><br>[[File:GioGearNestedInterior.jpg|left|thumb|200px]]<br clear=all> | ||
# Cut a ring from the small plastic tube and fit it around this assembly to prevent rattling. Place the assembly into the remaining barrel front in the reversed orientation shown: its narrow end faces the barrel and its wider opening faces outward.<br>[[File:GioGearExplodedAssembly.jpg|left|thumb|200px]]<br clear=all> | |||
# Fit the prepared outer cap over the assembly. Stretch a section of plastic tube over the cap so that it joins the cap to the barrel front and retains the nested pieces. Repeat at the other end. Add stretched plastic-tube sections to the barrels as decorative grips.<br>[[File:GioGearEndAssembly.jpg|left|thumb|200px]]<br clear=all> | |||
# Separate | # Fit a 1 cm plastic-tube sleeve over the centre of an approximately 4 cm SuperTips-diameter barrel connector. Join both Giotto barrels over this connector.<br>[[File:GioGearFinished.jpg|left|thumb|200px]]<br clear=all> | ||
<br>[[File: | |||
# | |||
# | |||
# | |||
# | |||
==References== | ==References== | ||
<references /> | |||
[[Category:Pen Mods]] | [[Category:Pen Mods]] | ||
Latest revision as of 16:18, 3 October 2026
The GioGear is a Titan Gear type mod invented by Magiai as the cheapest possible variation of the Titan Gear.
Construction
Parts needed
List from Magiai's blog:[1]
- 2x Giotto Turbo Maxi (Everything except ink and backplugs)
- 1x Small plastic tube
- The non-stretched one used in the tutorial can fit inside a Flexgrip
- 1x SuperTips-diameter barrel section (approximately 4 cm; centre connector)
Text tutorial[2]
- Empty both Giotto Turbo Maxi barrels. Cut and retain 7 mm from the front of each barrel.
- Scrape out the obstruction inside both retained front sections, as shown by the before-and-after photograph.
- Separate each cap’s inner part from its outer shell. Retain 3 cm of the cap’s flat outer section and cut 8 mm from the flat end of the inner part.
- Fit the flat inner-cap section over the narrow end of the retained Giotto front section. Fit the remaining inner-cap piece inside its wider opening.
- Cut a ring from the small plastic tube and fit it around this assembly to prevent rattling. Place the assembly into the remaining barrel front in the reversed orientation shown: its narrow end faces the barrel and its wider opening faces outward.
- Fit the prepared outer cap over the assembly. Stretch a section of plastic tube over the cap so that it joins the cap to the barrel front and retains the nested pieces. Repeat at the other end. Add stretched plastic-tube sections to the barrels as decorative grips.
- Fit a 1 cm plastic-tube sleeve over the centre of an approximately 4 cm SuperTips-diameter barrel connector. Join both Giotto barrels over this connector.
References
- ↑ tutorial from Magiai's blog
- ↑ GioGear tutorial, photographs by Magiai.