Kzzn Emboss: Difference between revisions
From Fen Spinner Wiki
More actions
No edit summary |
|||
| (12 intermediate revisions by 4 users not shown) | |||
| Line 5: | Line 5: | ||
|style= [[Double Sided]] | |style= [[Double Sided]] | ||
|length= 22cm | |length= 22cm | ||
|weight= | |weight= 27g | ||
|cog=COP | |cog=COP | ||
}} | }} | ||
| Line 13: | Line 13: | ||
===Parts needed=== | ===Parts needed=== | ||
List from [[Kzzn]]'s blog | List from [[Kzzn]]'s blog.<ref>[http://kazunoko1002.blog.fc2.com/blog-entry-41.html#more Kzzn's blog]</ref> | ||
* 2x [[Dr.Grip HDG-50R]] (tips) | * 2x [[Dr. Grip Shaker|Dr. Grip HDG-50R]] (tips) | ||
* 4x [[Pilot | * 4x [[Pilot SuperGrip|Supergrip]] (grips) | ||
* 2x [[Airblanc]] ( | * 2x [[Pilot AirBlanc|Airblanc]] (Tips) | ||
* 2x [[Pentel Hybrid Gel Roller|HGR]] ( | * 2x [[Pentel Hybrid Gel Roller|HGR]] (back caps) | ||
* 1x [[Penzgear]] (rings) | * 1x [[Penzgear]] (four rings) | ||
* 2x [[Tsukineko Emboss Dual Pen|Emboss]] (barrels) | * 2x [[Tsukineko Emboss Dual Pen|Emboss]] (barrels) | ||
* 2x [[Pilot G3|G3]] (rubber | * 2x [[Pilot G3|G3]] (cap rubber stoppers, grips) | ||
* 1x [[Dong-A Anyball|Anyball]] ( | * 1x [[Dong-A Anyball|Anyball]] (Grips, two is optional) | ||
* 1x [[Zebra Hyperjell|Hyperjell]] ( | * 1x [[Zebra Hyperjell|Hyperjell]] (Grip) | ||
===Text | ===Text tutorial<ref>[https://penmodding.pm/archives/5324 Kzzn Emboss written tutorial]</ref>=== | ||
# Empty | ====Preparation==== | ||
# | # Empty both Emboss markers. Retain, clean, and dry their felt writing nibs for use as connectors. | ||
# From one barrel, cut a 4.2 cm section from the front and another from the rear, excluding the writing nib from the measurement. Keep the second barrel as the centre section. | |||
# Fit a smooth SuperGrip section onto each cut extension, followed by a 5–7 mm Hyperjell section. Leave the openings accessible for the weight assemblies.<br>[[File:Kzznemboss1.jpg|left|thumb|200px]]<br clear=all> | |||
====Weight assemblies==== | |||
# Cut each HGR backplug to retain a 5 mm piece. Fit two Pen’z Gear rings onto each retained piece and screw it onto an Airblanc tip. | |||
# Fit one G3 grip ring around each HGR backplug and two SuperGrip rings around each Airblanc tip. | |||
# Place a G3 cap rubber stopper inside each Dr. Grip tip. Remove the narrow writing-end projection from each Dr. Grip tip by sanding or cutting it. | |||
# Insert each prepared Airblanc assembly into a Dr. Grip tip. Use the remaining smooth SuperGrip sections to hold these assemblies at the outer ends of the Emboss extensions.<br>[[File:Kzznemboss2.jpg|left|thumb|200px]]<br clear=all> | |||
# Fit four Anyball rings over each outer assembly. | |||
====Final assembly==== | |||
# Refit the cleaned felt nibs as connectors. Fit one SuperGrip ring at each nib-side joint, then use aluminium tape, or clear tape as permitted by the original tutorial, to secure the extensions to the centre barrel. | |||
===Video tutorial=== | |||
<youtube>https://youtu.be/tdp77_vWbrk</youtube> | |||
Video tutorial by Septoptus. | |||
==References== | |||
<references /> | |||
[[Category: Pen Mods]] | |||
Latest revision as of 19:20, 1 October 2026
Kzzn Emboss is a Double Sided mod created by JEB based spinner Kzzn.
Construction
Parts needed
- 2x Dr. Grip HDG-50R (tips)
- 4x Supergrip (grips)
- 2x Airblanc (Tips)
- 2x HGR (back caps)
- 1x Penzgear (four rings)
- 2x Emboss (barrels)
- 2x G3 (cap rubber stoppers, grips)
- 1x Anyball (Grips, two is optional)
- 1x Hyperjell (Grip)
Text tutorial[2]
Preparation
- Empty both Emboss markers. Retain, clean, and dry their felt writing nibs for use as connectors.
- From one barrel, cut a 4.2 cm section from the front and another from the rear, excluding the writing nib from the measurement. Keep the second barrel as the centre section.
- Fit a smooth SuperGrip section onto each cut extension, followed by a 5–7 mm Hyperjell section. Leave the openings accessible for the weight assemblies.
Weight assemblies
- Cut each HGR backplug to retain a 5 mm piece. Fit two Pen’z Gear rings onto each retained piece and screw it onto an Airblanc tip.
- Fit one G3 grip ring around each HGR backplug and two SuperGrip rings around each Airblanc tip.
- Place a G3 cap rubber stopper inside each Dr. Grip tip. Remove the narrow writing-end projection from each Dr. Grip tip by sanding or cutting it.
- Insert each prepared Airblanc assembly into a Dr. Grip tip. Use the remaining smooth SuperGrip sections to hold these assemblies at the outer ends of the Emboss extensions.
- Fit four Anyball rings over each outer assembly.
Final assembly
- Refit the cleaned felt nibs as connectors. Fit one SuperGrip ring at each nib-side joint, then use aluminium tape, or clear tape as permitted by the original tutorial, to secure the extensions to the centre barrel.
Video tutorial
Video tutorial by Septoptus.