Akiza G3: Difference between revisions
From Fen Spinner Wiki
More actions
Created page with "{{Mod Infobox |name= |image={{#setmainimage:Akiza_G3.jpg}} |creator= Akiza |style= Single Sided |length= ?cm |weight= ?g |cog= }} The '''Akiza G3''' is a personal mod made by JEB spinner Akiza. This tutorial isn't official as the tutorial for the legit one is secret. ==Construction== ===Parts needed=== List from the picture below: * 2x G3 (barrel, grip) * 1x Pilot G1 (tip) * 2x Hyperjell (2 grips) * 1x Zebra Jimnie (..." |
m Copyedit: spelling and grammar |
||
| (One intermediate revision by one other user not shown) | |||
| Line 8: | Line 8: | ||
|cog= | |cog= | ||
}} | }} | ||
The '''Akiza G3''' is a personal mod made by [[JEB]] spinner Akiza. This tutorial | The '''Akiza G3''' is a personal mod made by [[JEB]] spinner Akiza. This tutorial is unofficial because the original tutorial is secret. | ||
==Construction== | ==Construction== | ||
| Line 28: | Line 28: | ||
===Text tutorial=== | ===Text tutorial=== | ||
[[File:Akizatut.jpg|thumb|200px|Cropped picture of the non-official tutorial]] | |||
====Preparation==== | ====Preparation==== | ||
# Sand the nub and the front of the G3 barrel. | # Sand the nub and the front of the G3 barrel. | ||
# Cut the big ring of the | # Cut the big ring of the Anyball grip, then cut 5 blocks of Anyball grip. | ||
# Cut ~ | # Cut ~2 cm out of one Hyperjell grip. | ||
# Cut the clip of the Jimnie cap. | # Cut the clip of the Jimnie cap. | ||
====Assembly==== | ====Assembly==== | ||
=====Front side===== | =====Front side===== | ||
# Put the | # Put the 2 cm of Hyperjell grip on the front of the G3 barrel. | ||
# Put the big ring of anyball grip on the G1 tip. | # Put the big ring of anyball grip on the G1 tip. | ||
# Put the G1 tip inside the | # Put the G1 tip inside the large end of the Emboss cap (it should fit snugly). | ||
# Connect the Emboss cap to the front of the G3 barrel. | # Connect the Emboss cap to the front of the G3 barrel. | ||
# Add a ~4mm vinyl tape stripe on the Emboss cap's base. | # Add a ~4mm vinyl tape stripe on the Emboss cap's base. | ||
Latest revision as of 12:49, 27 August 2026
The Akiza G3 is a personal mod made by JEB spinner Akiza. This tutorial is unofficial because the original tutorial is secret.
Construction
Parts needed
List from the picture below:
- 2x G3 (barrel, grip)
- 1x Pilot G1 (tip)
- 2x Hyperjell (2 grips)
- 1x Zebra Jimnie (cap)
- 1x Anyball (grip)
- 1x Tsukineko Emboss (big cap)
- 1x Gel roller (tip)
Additional Items
- Vinyl tape
- Any other kind of tape
- An insert
Text tutorial
Preparation
- Sand the nub and the front of the G3 barrel.
- Cut the big ring of the Anyball grip, then cut 5 blocks of Anyball grip.
- Cut ~2 cm out of one Hyperjell grip.
- Cut the clip of the Jimnie cap.
Assembly
Front side
- Put the 2 cm of Hyperjell grip on the front of the G3 barrel.
- Put the big ring of anyball grip on the G1 tip.
- Put the G1 tip inside the large end of the Emboss cap (it should fit snugly).
- Connect the Emboss cap to the front of the G3 barrel.
- Add a ~4mm vinyl tape stripe on the Emboss cap's base.
Cap side
- Put 5 blocks of Anyball grip on the Jimnie cap.
- Put the Gel roller tip inside the Jimnie cap, add the other Hyperjell grip, and then press it inside the cap.
- Add some tape on the end of the G3 barrel, then connect the Jimnie cap to it.