White Stick V2 - Revision history

Garynotethan: /* Text Tutorial */

2025-07-22T20:08:28Z

Text Tutorial

← Older revision		Revision as of 20:08, 22 July 2025
Line 38:		Line 38:
	# Place the 5mm Tru Red Ballpoint Stick Pen grip on your Pilot Opt/Nextage tip. Place it inverted into the tip side of the 3.62 sub-body piece. The grip should be touching the end of the sub-body, not the base of the tip (see [https://youtu.be/Vl1JAtD8r8A?t=1581 26:21]). It is placed there to make the silhouette of the mod more flat and smooth. This is the "cap" of the pen.		# Place the 5mm Tru Red Ballpoint Stick Pen grip on your Pilot Opt/Nextage tip. Place it inverted into the tip side of the 3.62 sub-body piece. The grip should be touching the end of the sub-body, not the base of the tip (see [https://youtu.be/Vl1JAtD8r8A?t=1581 26:21]). It is placed there to make the silhouette of the mod more flat and smooth. This is the "cap" of the pen.
	# Cut 3.00cm of 9mm ID x 12mm OD silicone tube and place it over the "cap". There can be a small 1mm overhang from the silicon tube.		# Cut 3.00cm of 9mm ID x 12mm OD silicone tube and place it over the "cap". There can be a small 1mm overhang from the silicon tube.
	# Of course, make sure steps 4 - here are done twice for both sides of the mod.		# Of course, make sure steps 7 - here are done twice for both sides of the mod.
	# Connect bodies from the backplug side to the middle connector. Plug caps into the tip side of the bodies. White Stick V2 is complete.		# Connect bodies from the backplug side to the middle connector. Plug caps into the tip side of the bodies. White Stick V2 is complete.

V 0 1 D: Formatting corrections

2025-05-24T16:03:12Z

Formatting corrections

← Older revision		Revision as of 16:03, 24 May 2025
Line 8:		Line 8:
	\|cog=COP		\|cog=COP
	}}		}}
	The '''[[White Stick V2]]''' is the second iteration of an aptly named mod made by ~~'''~~[[ProBloodBag]]~~'''~~. The mod was made with a focus on minimalism in appearance and structure. Aside from the ~~'''~~[[Tru Red Gripped Ballpoint Stick Pen]]~~'''~~, all parts are relatively obtainable internationally, and the mod can be made for ~$10 USD at scale with most of the cost being attributed to the ~~'''~~[[Pilot Opt Shaker]]~~'''~~.		The '''[[White Stick V2]]''' is the second iteration of an aptly named mod made by [[ProBloodBag]]. The mod was made with a focus on minimalism in appearance and structure. Aside from the [[Tru Red Gripped Ballpoint Stick Pen]], all parts are relatively obtainable internationally, and the mod can be made for ~$10 USD at scale with most of the cost being attributed to the [[Pilot Opt Shaker]].

Garynotethan at 04:20, 23 May 2025

2025-05-23T04:20:14Z

← Older revision		Revision as of 04:20, 23 May 2025
Line 38:		Line 38:
	# Place the 5mm Tru Red Ballpoint Stick Pen grip on your Pilot Opt/Nextage tip. Place it inverted into the tip side of the 3.62 sub-body piece. The grip should be touching the end of the sub-body, not the base of the tip (see [https://youtu.be/Vl1JAtD8r8A?t=1581 26:21]). It is placed there to make the silhouette of the mod more flat and smooth. This is the "cap" of the pen.		# Place the 5mm Tru Red Ballpoint Stick Pen grip on your Pilot Opt/Nextage tip. Place it inverted into the tip side of the 3.62 sub-body piece. The grip should be touching the end of the sub-body, not the base of the tip (see [https://youtu.be/Vl1JAtD8r8A?t=1581 26:21]). It is placed there to make the silhouette of the mod more flat and smooth. This is the "cap" of the pen.
	# Cut 3.00cm of 9mm ID x 12mm OD silicone tube and place it over the "cap". There can be a small 1mm overhang from the silicon tube.		# Cut 3.00cm of 9mm ID x 12mm OD silicone tube and place it over the "cap". There can be a small 1mm overhang from the silicon tube.
			# Of course, make sure steps 4 - here are done twice for both sides of the mod.
	# Connect bodies from the backplug side to the middle connector. Plug caps into the tip side of the bodies. White Stick V2 is complete.		# Connect bodies from the backplug side to the middle connector. Plug caps into the tip side of the bodies. White Stick V2 is complete.


	=== Video Tutorial===		=== Video Tutorial===

Garynotethan: /* Construction */ text tutorial added

2025-05-22T20:32:00Z

Construction: text tutorial added

@@ Line 16: / Line 16: @@
 ==Construction==
 ===Parts needed===
@@ Line 27: / Line 24: @@
 ** Not available in all countries, any 10mm OD piece for center connecter and thin grip (heatshrink) can be subbed in
 * 1x (9mm ID x 12mm OD) Food Grade Silicone Tube
 [[Category:Pen Mods]]

Garynotethan: /* Tutorial */

2025-05-22T18:42:33Z

Tutorial

← Older revision		Revision as of 18:42, 22 May 2025
Line 17:		Line 17:
	==Construction==		==Construction==

	===Tutorial===		=== Video Tutorial===
	https://youtu.be/Vl1JAtD8r8A?si=yU4VRmbvy_xT_0sl		<youtube>https://youtu.be/Vl1JAtD8r8A?si=yU4VRmbvy_xT_0sl</youtube>

	===Parts needed===		===Parts needed===

Garynotethan at 19:38, 20 May 2025

2025-05-20T19:38:03Z

← Older revision		Revision as of 19:38, 20 May 2025
Line 26:		Line 26:
	* 1x [[Tru Red Gripped Ballpoint Stick Pen]] (cap / grip)		* 1x [[Tru Red Gripped Ballpoint Stick Pen]] (cap / grip)
	** Not available in all countries, any 10mm OD piece for center connecter and thin grip (heatshrink) can be subbed in		** Not available in all countries, any 10mm OD piece for center connecter and thin grip (heatshrink) can be subbed in
	* 2x (9mm ID x 12mm OD) Food Grade Silicone Tube		* 1x (9mm ID x 12mm OD) Food Grade Silicone Tube

	[[Category:Pen Mods]]		[[Category:Pen Mods]]

Probunga at 15:15, 1 January 2025

2025-01-01T15:15:05Z

← Older revision		Revision as of 15:15, 1 January 2025
Line 21:		Line 21:

	===Parts needed===		===Parts needed===
	* 2x [[Acrylic Paint Markers]] (barrel)		* 3x [[Acrylic Paint Markers]] (barrel)
	**Many duplicate subs, ensure 8.5cm length and 12mm OD		**Many duplicate subs, ensure 8.5cm length and 12mm OD
	* 2x [[Pilot Opt Shaker]] (tip / sub-body)		* 2x [[Pilot Opt Shaker]] (tip / sub-body)

Probunga: /* Parts needed */

2024-12-23T19:37:26Z

Parts needed

← Older revision		Revision as of 19:37, 23 December 2024
Line 21:		Line 21:

	===Parts needed===		===Parts needed===
	* 2x [[~~M&G~~ Acrylic Paint Markers]] (barrel)		* 2x [[Acrylic Paint Markers]] (barrel)
			**Many duplicate subs, ensure 8.5cm length and 12mm OD
	* 2x [[Pilot Opt Shaker]] (tip / sub-body)		* 2x [[Pilot Opt Shaker]] (tip / sub-body)
	* 1x [[Tru Red Gripped Ballpoint Stick Pen]] (cap / grip)		* 1x [[Tru Red Gripped Ballpoint Stick Pen]] (cap / grip)

Probunga at 19:35, 23 December 2024

2024-12-23T19:35:38Z

← Older revision		Revision as of 19:35, 23 December 2024
Line 8:		Line 8:
	\|cog=COP		\|cog=COP
	}}		}}
	The '''[[White Stick V2]]''' is the second iteration of an aptly named mod made by '''[[ProBloodBag]]'''. The mod was made with a focus on minimalism in appearance and structure~~, as well as having a good price to performance ratio~~. Aside from the '''[[Tru Red Gripped Ballpoint Stick Pen]]''', all parts ~~can be obtained from '''AliExpress'''~~, and the mod can be made for ~$10 USD at scale with most of the cost being attributed to the '''[[Pilot Opt Shaker]]'''.		The '''[[White Stick V2]]''' is the second iteration of an aptly named mod made by '''[[ProBloodBag]]'''. The mod was made with a focus on minimalism in appearance and structure. Aside from the '''[[Tru Red Gripped Ballpoint Stick Pen]]''', all parts are relatively obtainable internationally, and the mod can be made for ~$10 USD at scale with most of the cost being attributed to the '''[[Pilot Opt Shaker]]'''.

	The build process isn't difficult but can be made easier with a pipe cutter. Sanding is always recommended, especially for the '''[[Pilot Opt Shaker]]''' sub-body for the caps and '''[[M&G Acrylic Paint Markers]]''' barrel for the middle segment which will affect weight and length respectively. The hardest part of making the mod is cutting the silicone tube grips as close to 3cm as possible, however, having a great length of silicone tubing will give you more than enough tries. Depending on wear, the tips may begin to come loose over time, but this can be fixed with new silicone tube grips, or increasing the length of the '''[[Tru Red Gripped Ballpoint Stick Pen]]''' grip segment.

	~~Tutorial +~~ Images coming soon. (hopefully)		Cutting the silicone tubes has consistency issues due to curvature caused by the manufacturing process. Depending on wear, the tips may begin to come loose over time, but this can be fixed with new silicone tube grips, or increasing the length of the Tru Red grip segment.

			Images coming soon. (hopefully)

	==Construction==		==Construction==

			===Tutorial===
			https://youtu.be/Vl1JAtD8r8A?si=yU4VRmbvy_xT_0sl

	===Parts needed===		===Parts needed===

Probunga at 15:26, 30 July 2024

2024-07-30T15:26:42Z

← Older revision		Revision as of 15:26, 30 July 2024
Line 10:		Line 10:
	The '''[[White Stick V2]]''' is the second iteration of an aptly named mod made by '''[[ProBloodBag]]'''. The mod was made with a focus on minimalism in appearance and structure, as well as having a good price to performance ratio. Aside from the '''[[Tru Red Gripped Ballpoint Stick Pen]]''', all parts can be obtained from '''AliExpress''', and the mod can be made for ~$10 USD at scale with most of the cost being attributed to the '''[[Pilot Opt Shaker]]'''.		The '''[[White Stick V2]]''' is the second iteration of an aptly named mod made by '''[[ProBloodBag]]'''. The mod was made with a focus on minimalism in appearance and structure, as well as having a good price to performance ratio. Aside from the '''[[Tru Red Gripped Ballpoint Stick Pen]]''', all parts can be obtained from '''AliExpress''', and the mod can be made for ~$10 USD at scale with most of the cost being attributed to the '''[[Pilot Opt Shaker]]'''.

	The build process isn't difficult but can be made easier with a pipe cutter. Sanding is always recommended, especially for the '''[[Pilot Opt Shaker]]''' sub-body caps and '''[[M&G Acrylic Paint Markers]]''' middle ~~barrel~~ segment which will affect weight and length respectively. The hardest part of making the mod is cutting the silicone tube grips as close to 3cm as possible, however, having a great length of silicone tubing will give you more than enough tries. Depending on wear, the tips may begin to come loose over time, but this can be fixed with new silicone tube grips, or increasing the length of the '''[[Tru Red Gripped Ballpoint Stick Pen]]''' grip segment.		The build process isn't difficult but can be made easier with a pipe cutter. Sanding is always recommended, especially for the '''[[Pilot Opt Shaker]]''' sub-body for the caps and '''[[M&G Acrylic Paint Markers]]''' barrel for the middle segment which will affect weight and length respectively. The hardest part of making the mod is cutting the silicone tube grips as close to 3cm as possible, however, having a great length of silicone tubing will give you more than enough tries. Depending on wear, the tips may begin to come loose over time, but this can be fixed with new silicone tube grips, or increasing the length of the '''[[Tru Red Gripped Ballpoint Stick Pen]]''' grip segment.

	Tutorial + Images coming soon. (hopefully)		Tutorial + Images coming soon. (hopefully)