Magiai at 23:11, 30 January 2025

2025-01-30T23:11:26Z

← Older revision		Revision as of 23:11, 30 January 2025
Line 8:		Line 8:
	\|cog= cop		\|cog= cop
	}}		}}
	The '''Pall Emboss''' is a double-sided mod made by [[Fen]] spinner [[Varoza]] for Pall's [[Pen Spinning World Tournament 2021\|\|WT21]] combo.		The '''Pall Emboss''' is a double-sided mod made by [[Fen Spinner\|Fen]] spinner [[Varoza]] for Pall's [[Pen Spinning World Tournament 2021\|WT21]] combo.
	==Construction==		==Construction==

Magiai: Created page with "{{Mod Infobox |name= |image={{#setmainimage:Pallemboss.jpg}} |creator= Varoza |style= Double Sided |length= ~25cm |weight= ?g |cog= cop }} The '''Pall Emboss''' is a double-sided mod made by Fen spinner Varoza for Pall's WT21 combo. ==Construction== ===Parts needed=== List from IMPC: * x2 Tsukineko Fabrico / Tsukineko Emboss (body, cap and 1 back plugs) * x2 Pilot Dr. Grip (gr..."

2025-01-30T23:10:50Z

Created page with "{{Mod Infobox |name= |image={{#setmainimage:Pallemboss.jpg}} |creator= Varoza |style= Double Sided |length= ~25cm |weight= ?g |cog= cop }} The '''Pall Emboss''' is a double-sided mod made by Fen spinner Varoza for Pall's |WT21 combo. ==Construction== ===Parts needed=== List from IMPC: * x2 Tsukineko Fabrico / Tsukineko Emboss (body, cap and 1 back plugs) * x2 Pilot Dr. Grip (gr..."

New page

{{Mod Infobox
|name=
|image={{#setmainimage:Pallemboss.jpg}}
|creator= [[Varoza]]
|style= [[Double Sided]]
|length= ~25cm
|weight= ?g
|cog= cop
}}
The '''Pall Emboss''' is a double-sided mod made by [[Fen]] spinner [[Varoza]] for Pall's [[Pen Spinning World Tournament 2021||WT21]] combo.
==Construction==

===Parts needed===

List from IMPC:
* x2 [[Tsukineko Fabrico]] / [[Tsukineko Emboss Dual Pen|Tsukineko Emboss]] (body, cap and 1 back plugs)
* x2 [[Pilot Dr. Grip]] (grips)
** It is possible to use only one, but the symmetry will be slightly different.
* x2 [[Pilot AirBlanc]] (tips)
* x2 [[Pentel Hybrid Gel Roller]] (tips)
====Additional Items====
* Tape
* Heatshrink tube
* Glue

===Text tutorial===
====Preparation====
# Cut the heat-shrink tube to around 2 6cm section (around 3cm is visible when the mod is completed).
# Cut the Emboss front plug to around 1cm.
# Cut both Dr.grip grips in half.
# Cut both Emboss small caps so that they are assembled with a backplug in the middle, the result is ~24cm.

====Assembly====

# Glue the HGR tip onto the Airblanc tip.
# Wrap some tape around the tipstack.
# Put the small Emboss cap on the cut Emboss plug.
# Put the tipstack inside the small Emboss cap (it should be tight inside the cap).
# Put the heat-shrink tube on the cap and heat it. A lip should be created to keep the tips in place. Around 5.5cm should still be flat on the body.
# Put the Dr.grip grip half on the extremity of the Emboss base.
# Repeat on the other side.
# Connect both bases on the Emboss backplug.

==References==

[[Category:Pen Mods]]

Pall Emboss - Revision history

Magiai at 23:11, 30 January 2025