V 0 1 D: Restore Jedo mechanism insertion; correct glue location to the tip/barrel joint; clarify the image caption and G3 donor parts.

2026-10-01T18:50:48Z

Restore Jedo mechanism insertion; correct glue location to the tip/barrel joint; clarify the image caption and G3 donor parts.

← Older revision		Revision as of 18:50, 1 October 2026
Line 14:		Line 14:
	===Parts needed===		===Parts needed===
	List from the FPSB V2<ref name="Tutorial">https://thefpsbv2.penspinning.fr/viewtopic.php?t=5817</ref>:		List from the FPSB V2<ref name="Tutorial">https://thefpsbv2.penspinning.fr/viewtopic.php?t=5817</ref>:
	* 1x [[Pilot G3\|G3]] (barrel, grip and cap)		* 1x [[Pilot G3\|G3]] (barrel, tip, grip and cap)
	* 1x Jedo (~~Inktube~~ and tip)		* 1x Jedo (pencil mechanism and tip)
	* 1x [[Pentel Hybrid Gel Grip\|HGG]] (tip and grip)		* 1x [[Pentel Hybrid Gel Grip\|HGG]] (tip and grip)

Line 24:		Line 24:

	===Text tutorial===		===Text tutorial===

	====Preparation====		====Preparation====
	# Remove the g3 grip without cutting it.		# Remove the G3 grip without cutting it.
	# File the bump of the g3 barrel.		# File down the bump at the front of the G3 barrel.
	# Cut the ~~thread part of the g3~~ front (including ~~it's~~ bump).		# Cut off the threaded front section, including the bump.

	====Assembly====		====Assembly====
	=====Front side=====		=====Front side=====
	# Glue the ~~Jedo~~ tip to ~~its tube (without gluing~~ the mechanism).<br>[[File:Jedotipgjh.jpg\|left\|thumb\|200px\|Jedo tip ~~glued to it's mechanism~~]]<br clear=all>		# Insert the Jedo pencil mechanism through the rear of the prepared G3 barrel.
	# ~~Add~~ the HGG tip and grip ~~on at the front, glue~~ the HGG tip ~~onto~~ the Jedo tip if ~~necessary~~.		# Screw the Jedo tip onto its mechanism from the front. Glue the tip to the front of the G3 barrel, keeping the moving mechanism free of glue.<br>[[File:Jedotipgjh.jpg\|left\|thumb\|200px\|Jedo tip assembly.]]<br clear=all>
			# Fit the HGG tip over the Jedo tip and add the HGG grip. Glue the HGG tip to the Jedo tip if needed.

	=====Cap side=====		=====Cap side=====
	# ~~Put~~ the g3 tip and grip ~~(in this order) inside~~ the G3 cap.		# Insert the G3 tip and G3 grip into the G3 cap, in that order.
	# ~~Add some~~ tape on the ~~end~~ of the G3 barrel~~, then connect~~ the G3 cap ~~to it~~.		# Wrap tape around the rear of the G3 barrel and attach the cap.


	==References==		==References==

Magiai: Created page with "{{Mod Infobox |name= |image={{#setmainimage:GJH Mod.jpg}} |creator= Mr.LSC |style= Single Sided |length= 19cm |weight= ?g |cog= }} The '''GJH''' is a single sided writable mod made by PDS spinner Mr.LSC. Its name is an acronym of the 3 parts used. ==Construction== ===Parts needed=== List from the FPSB V2https://thefpsbv2.penspinning.fr/viewtopic.php?t=5817: * 1x G3 (barrel, grip and cap) * 1x Jedo (Inktube and tip..."

2025-01-05T01:19:08Z

Created page with "{{Mod Infobox |name= |image={{#setmainimage:GJH Mod.jpg}} |creator= Mr.LSC |style= Single Sided |length= 19cm |weight= ?g |cog= }} The '''GJH''' is a single sided writable mod made by PDS spinner Mr.LSC. Its name is an acronym of the 3 parts used. ==Construction== ===Parts needed=== List from the FPSB V2<ref name="Tutorial">https://thefpsbv2.penspinning.fr/viewtopic.php?t=5817</ref>: * 1x G3 (barrel, grip and cap) * 1x Jedo (Inktube and tip..."

New page

{{Mod Infobox
|name=
|image={{#setmainimage:GJH Mod.jpg}}
|creator= [[Mr.LSC]]
|style= [[Single Sided]]
|length= 19cm
|weight= ?g
|cog=
}}
The '''GJH''' is a single sided writable mod made by [[PDS]] spinner [[Mr.LSC]]. Its name is an acronym of the 3 parts used.

==Construction==

===Parts needed===
List from the FPSB V2<ref name="Tutorial">https://thefpsbv2.penspinning.fr/viewtopic.php?t=5817</ref>:
* 1x [[Pilot G3|G3]] (barrel, grip and cap)
* 1x Jedo (Inktube and tip)
* 1x [[Pentel Hybrid Gel Grip|HGG]] (tip and grip)

====Additional Items====
* Tape
* An insert
* Glue

===Text tutorial===

====Preparation====
# Remove the g3 grip without cutting it.
# File the bump of the g3 barrel.
# Cut the thread part of the g3 front (including it's bump).

====Assembly====
=====Front side=====
# Glue the Jedo tip to its tube (without gluing the mechanism).<br>[[File:Jedotipgjh.jpg|left|thumb|200px|Jedo tip glued to it's mechanism]]<br clear=all>
# Add the HGG tip and grip on at the front, glue the HGG tip onto the Jedo tip if necessary.

=====Cap side=====
# Put the g3 tip and grip (in this order) inside the G3 cap.
# Add some tape on the end of the G3 barrel, then connect the G3 cap to it.

==References==
<references />

[[Category:Pen Mods]] [[Category:G3 Mods]]

GJH - Revision history

V 0 1 D: Restore Jedo mechanism insertion; correct glue location to the tip/barrel joint; clarify the image caption and G3 donor parts.