Fen Spinner Wiki - User contributions [en]

Dark Mod Zero

2024-10-20T00:44:30Z

Orctupus:

{{Mod Infobox
|name=Dark Mod Zero
|image=DARKMOD ZERO FAR.jpg
|creator= Orctupus
|style= [[Double Sided]]
|length= 25.6cm
|weight= 30g
|cog= COP
}}
The '''Dark Mod Zero''' is a personal mod made by spinner [https://www.youtube.com/@Orctupus Orctupus YouTube]. It features a soft-gripped body similar to the [[Papermate Flexgrip Ultra]] that has the ability to grip the hand but still slip efficiently. This balance leads to a unique spinning experience with spinners who want a bit more control compared to traditional plastic lacquers found on most pens and markers.

==Construction==

===Parts needed===
Source: Directly Published here by Orctupus
[[File:DARKMOD_ZERO_MATERIALS.jpg|thumb|200px]]
* 2x [[9/32 - 5/16th Screw-in Target Point]] (Tip)
* 2x [[Pentel Energel Kuro]] (Body)
* 2x [[Pilot G2]] (Grip)
* 2x [[TUL Ballpoint Retractable]] (Grip)
* 3x [[Papermate Profile | Dong-a Anyball]] (Grip)
* 1x [[Papermate Officemate]] (Barrel)

====Additional Items====
* Painters Tape | Paper Tape
* Utility Knife
* OPTIONAL: Pipe-Cutter
* Scissor End | Thin Metal Rod (To push the Energel Kuro Clicker housing out of the body)

===Text tutorial===
* Disassemble the [[Pentel Energel Kuro]] pens by unscrewing the tips (Set aside), removing the metal ring, ink-tube, breaking the clip, and popping out the back of the retractable clicker mechanism through the lower square hole leaving only the bodies.

* Measure and cut the [[Pentel Energel Kuro]] bodies 1cm from the back of the pen (clicker mechanism side) using a utility knife or pipe-cutter. Once both body's are cut, set aside.

* Disassemble the [[Papermate Officemate]] removing the front plug and ink-tube leaving only the barrel.

* Measure and cut the [[Papermate Officemate]] barrel 3.2cm from the front of the pen (Set aside).
* Disassemble the [[TUL Ballpoint Retractable]] pens removing the front tip, metal ring, ink-tube, and set aside the Grips.
* Disassemble the [[Pilot G2]] pens removing only the grips and set aside

* Cut 2x 8-Sections of Grip from two of the [[Papermate profile | Dong-a Anyball]] grips. Set aside.

* Cut 2x 4-Sections of Grip from one of the [[Papermate profile | Dong-a Anyball]] grip. Set aside

* Stretch the [[Pilot G2]] Grips using a pliers. Set aside.

* Wrap 2x the [[9/32 - 5/16th Screw-in Target Point]] tips with Painters Tape or Paper Tape around the base until they can be placed snug into the [[Pentel Energel Kuro]] front barrel (threaded side).

* Place the [[Pentel Energel Kuro]] tips loosely over the [[9/32 - 5/16th Screw-in Target Point]] tips and then push the [[TUL Ballpoint Retractable]] grip over both the tips and onto the barrel. (there will be a slight bump on the inner 1/3rd of the TUL grip.)

* Stretch the [[Pilot G2]] Grip up and over the [[TUL Ballpoint Retractable]] Grip with the G2 rings facing outwards till the [[Pentel Energel Kuro]] tip is only seen about 2-3mm and there is 2-3mm of the TUL grip showing on the other side.

* Place the 2x 8-Sections of [[Papermate profile | Dong-a Anyball]] grips on the other side of each [[Pentel Energel Kuro]] barrel. You want to have a flat section facing inwards vs the smooth thinner end on the inside. Slide it up against the [[Pilot G2]] Grip.

* Place the 2x 4-Sections of [[Papermate profile | Dong-a Anyball]] grips on the ring side of the [[Pilot G2]] grip on each side.

* Use the [[Papermate Officemate]] 3.2cm cut body section to join the [[Pentel Energel Kuro]] Barrels and then put both sides together press-fit over the officemate section.

* FINISHED

====Assembly====
!!! IN PROGRESS !!!

===Video Tutorial===
!!! COMING SOON !!!

==References==
<references />

[[Category:Pen Mods]]]

Dark Mod Zero

2024-10-20T00:38:27Z

Orctupus: /* Text tutorial */

{{Mod Infobox
|name=Dark Mod Zero
|image=DARKMOD ZERO FAR.jpg
|creator= Orctupus
|style= [[Double Sided]]
|length= 25.6cm
|weight= 30g
|cog= COP
}}
The '''Dark Mod Zero''' is a personal mod made by spinner Orctupus [https://www.youtube.com/@Orctupus Orctupus YouTube].

==Construction==

===Parts needed===
Source: Directly Published here by Orctupus
[[File:DARKMOD_ZERO_MATERIALS.jpg|thumb|200px]]
* 2x [[9/32 - 5/16th Screw-in Target Point]] (Tip)
* 2x [[Pentel Energel Kuro]] (Body)
* 2x [[Pilot G2]] (Grip)
* 2x [[TUL Ballpoint Retractable]] (Grip)
* 3x [[Papermate Profile | Dong-a Anyball]] (Grip)
* 1x [[Papermate Officemate]] (Barrel)

====Additional Items====
* Painters Tape | Paper Tape
* Utility Knife
* OPTIONAL: Pipe-Cutter
* Scissor End | Thin Metal Rod (To push the Energel Kuro Clicker housing out of the body)

===Text tutorial===
* Disassemble the [[Pentel Energel Kuro]] pens by unscrewing the tips (Set aside), removing the metal ring, ink-tube, breaking the clip, and popping out the back of the retractable clicker mechanism through the lower square hole leaving only the bodies.

* Measure and cut the [[Pentel Energel Kuro]] bodies 1cm from the back of the pen (clicker mechanism side) using a utility knife or pipe-cutter. Once both body's are cut, set aside.

* Disassemble the [[Papermate Officemate]] removing the front plug and ink-tube leaving only the barrel.

* Measure and cut the [[Papermate Officemate]] barrel 3.2cm from the front of the pen (Set aside).
* Disassemble the [[TUL Ballpoint Retractable]] pens removing the front tip, metal ring, ink-tube, and set aside the Grips.
* Disassemble the [[Pilot G2]] pens removing only the grips and set aside

* Cut 2x 8-Sections of Grip from two of the [[Papermate profile | Dong-a Anyball]] grips. Set aside.

* Cut 2x 4-Sections of Grip from one of the [[Papermate profile | Dong-a Anyball]] grip. Set aside

* Stretch the [[Pilot G2]] Grips using a pliers. Set aside.

* Wrap 2x the [[9/32 - 5/16th Screw-in Target Point]] tips with Painters Tape or Paper Tape around the base until they can be placed snug into the [[Pentel Energel Kuro]] front barrel (threaded side).

* Place the [[Pentel Energel Kuro]] tips loosely over the [[9/32 - 5/16th Screw-in Target Point]] tips and then push the [[TUL Ballpoint Retractable]] grip over both the tips and onto the barrel. (there will be a slight bump on the inner 1/3rd of the TUL grip.)

* Stretch the [[Pilot G2]] Grip up and over the [[TUL Ballpoint Retractable]] Grip with the G2 rings facing outwards till the [[Pentel Energel Kuro]] tip is only seen about 2-3mm and there is 2-3mm of the TUL grip showing on the other side.

* Place the 2x 8-Sections of [[Papermate profile | Dong-a Anyball]] grips on the other side of each [[Pentel Energel Kuro]] barrel. You want to have a flat section facing inwards vs the smooth thinner end on the inside. Slide it up against the [[Pilot G2]] Grip.

* Place the 2x 4-Sections of [[Papermate profile | Dong-a Anyball]] grips on the ring side of the [[Pilot G2]] grip on each side.

* Use the [[Papermate Officemate]] 3.2cm cut body section to join the [[Pentel Energel Kuro]] Barrels and then put both sides together press-fit over the officemate section.

* FINISHED

====Assembly====
!!! IN PROGRESS !!!

===Video Tutorial===
!!! COMING SOON !!!

==References==
<references />

[[Category:Pen Mods]]]

Dark Mod Zero

2024-10-20T00:37:25Z

Orctupus: /* Text tutorial */

{{Mod Infobox
|name=Dark Mod Zero
|image=DARKMOD ZERO FAR.jpg
|creator= Orctupus
|style= [[Double Sided]]
|length= 25.6cm
|weight= 30g
|cog= COP
}}
The '''Dark Mod Zero''' is a personal mod made by spinner Orctupus [https://www.youtube.com/@Orctupus Orctupus YouTube].

==Construction==

===Parts needed===
Source: Directly Published here by Orctupus
[[File:DARKMOD_ZERO_MATERIALS.jpg|thumb|200px]]
* 2x [[9/32 - 5/16th Screw-in Target Point]] (Tip)
* 2x [[Pentel Energel Kuro]] (Body)
* 2x [[Pilot G2]] (Grip)
* 2x [[TUL Ballpoint Retractable]] (Grip)
* 3x [[Papermate Profile | Dong-a Anyball]] (Grip)
* 1x [[Papermate Officemate]] (Barrel)

====Additional Items====
* Painters Tape | Paper Tape
* Utility Knife
* OPTIONAL: Pipe-Cutter
* Scissor End | Thin Metal Rod (To push the Energel Kuro Clicker housing out of the body)

===Text tutorial===
1 Disassemble the [[Pentel Energel Kuro]] pens by unscrewing the tips (Set aside), removing the metal ring, ink-tube, breaking the clip, and popping out the back of the retractable clicker mechanism through the lower square hole leaving only the bodies.

2 Measure and cut the [[Pentel Energel Kuro]] bodies 1cm from the back of the pen (clicker mechanism side) using a utility knife or pipe-cutter. Once both body's are cut, set aside.

#3 Disassemble the [[Papermate Officemate]] removing the front plug and ink-tube leaving only the barrel.

4 Measure and cut the [[Papermate Officemate]] barrel 3.2cm from the front of the pen (Set aside).
#6 Disassemble the [[TUL Ballpoint Retractable]] pens removing the front tip, metal ring, ink-tube, and set aside the Grips.

#7 Disassemble the [[Pilot G2]] pens removing only the grips and set aside

8 Cut 2x 8-Sections of Grip from two of the [[Papermate profile | Dong-a Anyball]] grips. Set aside.

9 Cut 2x 4-Sections of Grip from one of the [[Papermate profile | Dong-a Anyball]] grip. Set aside

10 Stretch the [[Pilot G2]] Grips using a pliers. Set aside.

11 Wrap 2x the [[9/32 - 5/16th Screw-in Target Point]] tips with Painters Tape or Paper Tape around the base until they can be placed snug into the [[Pentel Energel Kuro]] front barrel (threaded side).

12 Place the [[Pentel Energel Kuro]] tips loosely over the [[9/32 - 5/16th Screw-in Target Point]] tips and then push the [[TUL Ballpoint Retractable]] grip over both the tips and onto the barrel. (there will be a slight bump on the inner 1/3rd of the TUL grip.)

13 Stretch the [[Pilot G2]] Grip up and over the [[TUL Ballpoint Retractable]] Grip with the G2 rings facing outwards till the [[Pentel Energel Kuro]] tip is only seen about 2-3mm and there is 2-3mm of the TUL grip showing on the other side.

14 Place the 2x 8-Sections of [[Papermate profile | Dong-a Anyball]] grips on the other side of each [[Pentel Energel Kuro]] barrel. You want to have a flat section facing inwards vs the smooth thinner end on the inside. Slide it up against the [[Pilot G2]] Grip.

15 Place the 2x 4-Sections of [[Papermate profile | Dong-a Anyball]] grips on the ring side of the [[Pilot G2]] grip on each side.

16 Use the [[Papermate Officemate]] 3.2cm cut body section to join the [[Pentel Energel Kuro]] Barrels and then put both sides together press-fit over the officemate section.

17 FINISHED

====Assembly====
!!! IN PROGRESS !!!

===Video Tutorial===
!!! COMING SOON !!!

==References==
<references />

[[Category:Pen Mods]]]

Dark Mod Zero

2024-10-20T00:36:59Z

Orctupus: /* Text tutorial */

{{Mod Infobox
|name=Dark Mod Zero
|image=DARKMOD ZERO FAR.jpg
|creator= Orctupus
|style= [[Double Sided]]
|length= 25.6cm
|weight= 30g
|cog= COP
}}
The '''Dark Mod Zero''' is a personal mod made by spinner Orctupus [https://www.youtube.com/@Orctupus Orctupus YouTube].

==Construction==

===Parts needed===
Source: Directly Published here by Orctupus
[[File:DARKMOD_ZERO_MATERIALS.jpg|thumb|200px]]
* 2x [[9/32 - 5/16th Screw-in Target Point]] (Tip)
* 2x [[Pentel Energel Kuro]] (Body)
* 2x [[Pilot G2]] (Grip)
* 2x [[TUL Ballpoint Retractable]] (Grip)
* 3x [[Papermate Profile | Dong-a Anyball]] (Grip)
* 1x [[Papermate Officemate]] (Barrel)

====Additional Items====
* Painters Tape | Paper Tape
* Utility Knife
* OPTIONAL: Pipe-Cutter
* Scissor End | Thin Metal Rod (To push the Energel Kuro Clicker housing out of the body)

===Text tutorial===
#1 Disassemble the [[Pentel Energel Kuro]] pens by unscrewing the tips (Set aside), removing the metal ring, ink-tube, breaking the clip, and popping out the back of the retractable clicker mechanism through the lower square hole leaving only the bodies.

#2 Measure and cut the [[Pentel Energel Kuro]] bodies 1cm from the back of the pen (clicker mechanism side) using a utility knife or pipe-cutter. Once both body's are cut, set aside.

#3 Disassemble the [[Papermate Officemate]] removing the front plug and ink-tube leaving only the barrel.

#4 Measure and cut the [[Papermate Officemate]] barrel 3.2cm from the front of the pen (Set aside).

#6 Disassemble the [[TUL Ballpoint Retractable]] pens removing the front tip, metal ring, ink-tube, and set aside the Grips.

#7 Disassemble the [[Pilot G2]] pens removing only the grips and set aside

#8 Cut 2x 8-Sections of Grip from two of the [[Papermate profile | Dong-a Anyball]] grips. Set aside.

#9 Cut 2x 4-Sections of Grip from one of the [[Papermate profile | Dong-a Anyball]] grip. Set aside

#10 Stretch the [[Pilot G2]] Grips using a pliers. Set aside.

#11 Wrap 2x the [[9/32 - 5/16th Screw-in Target Point]] tips with Painters Tape or Paper Tape around the base until they can be placed snug into the [[Pentel Energel Kuro]] front barrel (threaded side).

#12 Place the [[Pentel Energel Kuro]] tips loosely over the [[9/32 - 5/16th Screw-in Target Point]] tips and then push the [[TUL Ballpoint Retractable]] grip over both the tips and onto the barrel. (there will be a slight bump on the inner 1/3rd of the TUL grip.)

#13 Stretch the [[Pilot G2]] Grip up and over the [[TUL Ballpoint Retractable]] Grip with the G2 rings facing outwards till the [[Pentel Energel Kuro]] tip is only seen about 2-3mm and there is 2-3mm of the TUL grip showing on the other side.

#14 Place the 2x 8-Sections of [[Papermate profile | Dong-a Anyball]] grips on the other side of each [[Pentel Energel Kuro]] barrel. You want to have a flat section facing inwards vs the smooth thinner end on the inside. Slide it up against the [[Pilot G2]] Grip.

#15 Place the 2x 4-Sections of [[Papermate profile | Dong-a Anyball]] grips on the ring side of the [[Pilot G2]] grip on each side.

#16 Use the [[Papermate Officemate]] 3.2cm cut body section to join the [[Pentel Energel Kuro]] Barrels and then put both sides together press-fit over the officemate section.

#17 FINISHED

====Assembly====
!!! IN PROGRESS !!!

===Video Tutorial===
!!! COMING SOON !!!

==References==
<references />

[[Category:Pen Mods]]]

Dark Mod Zero

2024-10-20T00:36:06Z

Orctupus: /* Text tutorial */

{{Mod Infobox
|name=Dark Mod Zero
|image=DARKMOD ZERO FAR.jpg
|creator= Orctupus
|style= [[Double Sided]]
|length= 25.6cm
|weight= 30g
|cog= COP
}}
The '''Dark Mod Zero''' is a personal mod made by spinner Orctupus [https://www.youtube.com/@Orctupus Orctupus YouTube].

==Construction==

===Parts needed===
Source: Directly Published here by Orctupus
[[File:DARKMOD_ZERO_MATERIALS.jpg|thumb|200px]]
* 2x [[9/32 - 5/16th Screw-in Target Point]] (Tip)
* 2x [[Pentel Energel Kuro]] (Body)
* 2x [[Pilot G2]] (Grip)
* 2x [[TUL Ballpoint Retractable]] (Grip)
* 3x [[Papermate Profile | Dong-a Anyball]] (Grip)
* 1x [[Papermate Officemate]] (Barrel)

====Additional Items====
* Painters Tape | Paper Tape
* Utility Knife
* OPTIONAL: Pipe-Cutter
* Scissor End | Thin Metal Rod (To push the Energel Kuro Clicker housing out of the body)

===Text tutorial===
# Disassemble the [[Pentel Energel Kuro]] pens by unscrewing the tips (Set aside), removing the metal ring, ink-tube, breaking the clip, and popping out the back of the retractable clicker mechanism through the lower square hole leaving only the bodies.

# Measure and cut the [[Pentel Energel Kuro]] bodies 1cm from the back of the pen (clicker mechanism side) using a utility knife or pipe-cutter. Once both body's are cut, set aside.

# Disassemble the [[Papermate Officemate]] removing the front plug and ink-tube leaving only the barrel.

# Measure and cut the [[Papermate Officemate]] barrel 3.2cm from the front of the pen (Set aside).

# Disassemble the [[TUL Ballpoint Retractable]] pens removing the front tip, metal ring, ink-tube, and set aside the Grips.

# Disassemble the [[Pilot G2]] pens removing only the grips and set aside

# Cut 2x 8-Sections of Grip from two of the [[Papermate profile | Dong-a Anyball]] grips. Set aside.

# Cut 2x 4-Sections of Grip from one of the [[Papermate profile | Dong-a Anyball]] grip. Set aside

# Stretch the [[Pilot G2]] Grips using a pliers. Set aside.

# Wrap 2x the [[9/32 - 5/16th Screw-in Target Point]] tips with Painters Tape or Paper Tape around the base until they can be placed snug into the [[Pentel Energel Kuro]] front barrel (threaded side).

# Place the [[Pentel Energel Kuro]] tips loosely over the [[9/32 - 5/16th Screw-in Target Point]] tips and then push the [[TUL Ballpoint Retractable]] grip over both the tips and onto the barrel. (there will be a slight bump on the inner 1/3rd of the TUL grip.)

# Stretch the [[Pilot G2]] Grip up and over the [[TUL Ballpoint Retractable]] Grip with the G2 rings facing outwards till the [[Pentel Energel Kuro]] tip is only seen about 2-3mm and there is 2-3mm of the TUL grip showing on the other side.

# Place the 2x 8-Sections of [[Papermate profile | Dong-a Anyball]] grips on the other side of each [[Pentel Energel Kuro]] barrel. You want to have a flat section facing inwards vs the smooth thinner end on the inside. Slide it up against the [[Pilot G2]] Grip.

# Place the 2x 4-Sections of [[Papermate profile | Dong-a Anyball]] grips on the ring side of the [[Pilot G2]] grip on each side.

# Use the [[Papermate Officemate]] 3.2cm cut body section to join the [[Pentel Energel Kuro]] Barrels and then put both sides together press-fit over the officemate section.

# FINISHED

====Assembly====
!!! IN PROGRESS !!!

===Video Tutorial===
!!! COMING SOON !!!

==References==
<references />

[[Category:Pen Mods]]]

Dark Mod Zero

2024-10-19T17:38:25Z

Orctupus: This is a tutorial for creating the Dark Mod Zero mod by Orctupus

File:DARKMOD ZERO MATERIALS.jpg

2024-10-19T17:14:39Z

Orctupus:

Materials as Shown, 9/32nd 5/16th Archery Screw-in Tips, Pentel Energel Kuro, TUL Ballpoint Retractable, Pilot G2, Papermate Profile, Papermate Officemate

File:DARKMOD ZERO FAR.jpg

2024-10-19T16:26:11Z

Orctupus:

The Dark Mod Zero