Fen Spinner Wiki - User contributions [en]

Apogeum

2024-12-28T16:06:19Z

Krzys:

{{Mod Infobox
|name=Apogeum M8
|image={{#setmainimage:Apgmm.jpg}}
|creator= [[Mervo]]
|style= [[Double Sided]]
|length= 26cm
|weight= 50g
|cog=COP
}}
'''Apogeum M8''' (also known as The Lego Mod) is a bolt-tipped mod made by Polish [[PPP]]-based spinner [[Mervo]] in 2024. The mod is the 6th iteration since the original in 2019.
The mod is extremely cheap to make since it uses parts sourced from Temu, excluding the [[Giotto Turbo Maxi|Giotto Turbo Maxi ]]. It also uses bolts as tips. The cost of the mod is ~4€; the price could vary depending on the price of the [[Giotto Turbo Maxi|Giotto Turbo Maxi]].

The mod’s construction is very simple, but it requires a circular file in order to make the parts fit each other easier. Also, using boiling water to stretch out the grips so they can fit the "cap" is recommended. And it is also strongly advised to use a pipe cutter for proper cuts on the body.

==Construction==

===Parts needed===
[[File:Temu mod demo 2.jpg|left|thumb|300px|the temu mod]] 
* 3x [[Giotto Turbo Maxi|Giotto Turbo Maxi]] (Barrel, Backplug)
* 1x Temu mod (grips)(can be subbed with DGG but has a noticeable difference of 3 grams and overall feel)
* 1x [[Crayola SuperTips|Crayola Supertip]] (barrel) or alternative with the same width
* 2x M8 30mm bolts
====Additional tools====
* Pipe cutter
* Paper tape
* Circular file
====Additional information====
* You can use the silicone bits that stick out on the Temu mod and use them as decorative grips.
* The weight can be adjusted. For lighter mod use, shorter M8s.
* The length can also be adjusted. If you want a longer mod, elongate the Giotto section that goes on the Giotto backplug, or take a shorter M8 eg 20mm M8 with 1 M8 nut.
* File or sand down the sharp edges on the bolt to avoid damaging the grips.
* You can also use silicone tubing or clear grip for a different design.
[[File:Apogeum grip demo.jpg|left|thumb|300px|diffrent ideas of gripping the apogeum]] 
===Image Tutorial===

[[File:Apgmlegotut.jpg|left|thumb|300px|Image tutorial by Mervo. Click to expand]] 

[[Category:Pen Mods]]

File:Apgmlegotut.jpg

2024-12-28T16:04:53Z

Krzys:

lego/apogeum mod final tutroaial

Apogeum

2024-12-28T00:04:38Z

Krzys:

{{Mod Infobox
|name=Apogeum M8
|image={{#setmainimage:Apgmm.jpg}}
|creator= [[Mervo]]
|style= [[Double Sided]]
|length= 26cm
|weight= 50g
|cog=COP
}}
'''Apogeum M8''' (also known as The Lego Mod) is a bolt-tipped mod made by Polish [[PPP]]-based spinner [[Mervo]] in 2024. The mod is the 6th iteration since the original in 2019.
The mod is extremely cheap to make since it uses parts sourced from Temu, excluding the [[Giotto Turbo Maxi|Giotto Turbo Maxi ]]. It also uses bolts as tips. The cost of the mod is ~4€; the price could vary depending on the price of the [[Giotto Turbo Maxi|Giotto Turbo Maxi]].

The mod’s construction is very simple, but it requires a circular file in order to make the parts fit each other easier. Also, using boiling water to stretch out the grips so they can fit the "cap" is recommended. And it is also strongly advised to use a pipe cutter for proper cuts on the body.

==Construction==

===Parts needed===
[[File:Temu mod demo 2.jpg|left|thumb|300px|the temu mod]] 
* 3x [[Giotto Turbo Maxi|Giotto Turbo Maxi]] (Barrel, Backplug)
* 1x Temu mod (grips)(can be subbed with DGG but has a noticeable difference of 3 grams and overall feel)
* 1x [[Crayola SuperTips|Crayola Supertip]] (barrel) or alternative with the same width
* 2x M8 30mm bolts
====Additional tools====
* Pipe cutter
* Paper tape
* Circular file
====Additional information====
* You can use the silicone bits that stick out on the Temu mod and use them as decorative grips.
* The weight can be adjusted. For lighter mod use, shorter M8s.
* The length can also be adjusted. If you want a longer mod, elongate the Giotto section that goes on the Giotto backplug, or take a shorter M8 eg 20mm M8 with 1 M8 nut.
* File or sand down the sharp edges on the bolt to avoid damaging the grips.
* You can also use silicone tubing or clear grip for a different design.
[[File:Apogeum grip demo.jpg|left|thumb|300px|diffrent ideas of gripping the apogeum]] 
===Image Tutorial===

[[File:Apgg.jpg|left|thumb|300px|Image tutorial by Mervo. Click to expand]] 

[[Category:Pen Mods]]

Apogeum

2024-12-28T00:04:10Z

Krzys:

{{Mod Infobox
|name=Apogeum M8
|image={{#setmainimage:Apgmm.jpg}}
|creator= [[Mervo]]
|style= [[Double Sided]]
|length= 26cm
|weight= 50g
|cog=COP
}}
'''Apogeum M8''' (also known as The Lego Mod) is a bolt-tipped mod made by Polish [[PPP]]-based spinner [[Mervo]] in 2024. The mod is the 6th iteration since the original in 2019.
The mod is extremely cheap to make since it uses parts sourced from Temu, excluding the [[Giotto Turbo Maxi|Giotto Turbo Maxi ]]. It also uses bolts as tips. The cost of the mod is ~4€; the price could vary depending on the price of the [[Giotto Turbo Maxi|Giotto Turbo Maxi]].

The mod’s construction is very simple, but it requires a circular file in order to make the parts fit each other easier. Also, using boiling water to stretch out the grips so they can fit the "cap" is recommended. And it is also strongly advised to use a pipe cutter for proper cuts on the body.

==Construction==

===Parts needed===
[[File:Temu mod demo 2.jpg|left|thumb|300px|the temu mod]] 
* 3x [[Giotto Turbo Maxi|Giotto Turbo Maxi]] (Barrel, Backplug)
* 1x Temu mod (grips)(can be subbed with DGG but has a noticeable difference of 3 grams and overall feel)
* 1x [[Crayola SuperTips|Crayola Supertip]] (barrel) or alternative with the same width
* 2x M8 30mm bolts
====Additional tools====
* Pipe cutter
* Paper tape
* Circular file
====Additional information====
* You can use the silicone bits that stick out on the Temu mod and use them as decorative grips.
* The weight can be adjusted. For lighter mod use, shorter M8s.
* The length can also be adjusted. If you want a longer mod, elongate the Giotto section that goes on the Giotto backplug, or take a shorter M8 eg 20mm M8 with 1 M8 nut.
* File or sand down the sharp edges on the bolt to avoid damaging the grips.
* You can also use silicone tubing or clear grip for a different design.
[[File:Apogeum grip demo.jpg|left|thumb|300px]] 
===Image Tutorial===

[[File:Apgg.jpg|left|thumb|300px|Image tutorial by Mervo. Click to expand]] 

[[Category:Pen Mods]]

Apogeum

2024-12-28T00:03:12Z

Krzys:

{{Mod Infobox
|name=Apogeum M8
|image={{#setmainimage:Apgmm.jpg}}
|creator= [[Mervo]]
|style= [[Double Sided]]
|length= 26cm
|weight= 50g
|cog=COP
}}
'''Apogeum M8''' (also known as The Lego Mod) is a bolt-tipped mod made by Polish [[PPP]]-based spinner [[Mervo]] in 2024. The mod is the 6th iteration since the original in 2019.
The mod is extremely cheap to make since it uses parts sourced from Temu, excluding the [[Giotto Turbo Maxi|Giotto Turbo Maxi ]]. It also uses bolts as tips. The cost of the mod is ~4€; the price could vary depending on the price of the [[Giotto Turbo Maxi|Giotto Turbo Maxi]].

The mod’s construction is very simple, but it requires a circular file in order to make the parts fit each other easier. Also, using boiling water to stretch out the grips so they can fit the "cap" is recommended. And it is also strongly advised to use a pipe cutter for proper cuts on the body.

==Construction==

===Parts needed===
[[File:Temu mod demo 2.jpg|left|thumb|300px]] 
* 3x [[Giotto Turbo Maxi|Giotto Turbo Maxi]] (Barrel, Backplug)
* 1x Temu mod (grips)(can be subbed with DGG but has a noticeable difference of 3 grams and overall feel)
* 1x [[Crayola SuperTips|Crayola Supertip]] (barrel) or alternative with the same width
* 2x M8 30mm bolts
====Additional tools====
* Pipe cutter
* Paper tape
* Circular file
====Additional information====
* You can use the silicone bits that stick out on the Temu mod and use them as decorative grips.
* The weight can be adjusted. For lighter mod use, shorter M8s.
* The length can also be adjusted. If you want a longer mod, elongate the Giotto section that goes on the Giotto backplug, or take a shorter M8 eg 20mm M8 with 1 M8 nut.
* File or sand down the sharp edges on the bolt to avoid damaging the grips.
* You can also use silicone tubing or clear grip for a different design.
[[File:Apogeum grip demo.jpg|left|thumb|300px]] 
===Image Tutorial===

[[File:Apgg.jpg|left|thumb|300px|Image tutorial by Mervo. Click to expand]] 

[[Category:Pen Mods]]

Apogeum

2024-12-27T23:54:33Z

Krzys:

{{Mod Infobox
|name=Apogeum M8
|image={{#setmainimage:Apgmm.jpg}}
|creator= [[Mervo]]
|style= [[Double Sided]]
|length= 26cm
|weight= 50g
|cog=COP
}}
'''Apogeum M8''' (also known as The Lego Mod) is a bolt-tipped mod made by Polish [[PPP]]-based spinner [[Mervo]] in 2024. The mod is the 6th iteration since the original in 2019.
The mod is extremely cheap to make since it uses parts sourced from Temu, excluding the [[Giotto Turbo Maxi|Giotto Turbo Maxi ]]. It also uses bolts as tips. The cost of the mod is ~4€; the price could vary depending on the price of the [[Giotto Turbo Maxi|Giotto Turbo Maxi]].

The mod’s construction is very simple, but it requires a circular file in order to make the parts fit each other easier. Also, using boiling water to stretch out the grips so they can fit the "cap" is recommended. And it is also strongly advised to use a pipe cutter for proper cuts on the body.

==Construction==

===Parts needed===
[[File:Temu mod demo 2.jpg|thumb]]
* 3x [[Giotto Turbo Maxi|Giotto Turbo Maxi]] (Barrel, Backplug)
* 1x Temu mod (grips)(can be subbed with DGG but has a noticeable difference of 3 grams and overall feel)
* 1x [[Crayola SuperTips|Crayola Supertip]] (barrel) or alternative with the same width
* 2x M8 30mm bolts
====Additional tools====
* Pipe cutter
* Paper tape
* Circular file
====Additional information====
[[File:Apogeum grip demo.jpg|thumb]]
* You can use the silicone bits that stick out on the Temu mod and use them as decorative grips.
* The weight can be adjusted. For lighter mod use, shorter M8s.
* The length can also be adjusted. If you want a longer mod, elongate the Giotto section that goes on the Giotto backplug, or take a shorter M8 eg 20mm M8 with 1 M8 nut.
* File or sand down the sharp edges on the bolt to avoid damaging the grips.
* You can also use silicone tubing or clear grip for a different design.

===Image Tutorial===

[[File:Apgg.jpg|left|thumb|300px|Image tutorial by Mervo. Click to expand]] 

[[Category:Pen Mods]]

Apogeum

2024-12-27T23:53:44Z

Krzys:

{{Mod Infobox
|name=Apogeum M8
|image={{#setmainimage:Apgmm.jpg}}
|creator= [[Mervo]]
|style= [[Double Sided]]
|length= 26cm
|weight= 50g
|cog=COP
}}
'''Apogeum M8''' (also known as The Lego Mod) is a bolt-tipped mod made by Polish [[PPP]]-based spinner [[Mervo]] in 2024. The mod is the 6th iteration since the original in 2019.
The mod is extremely cheap to make since it uses parts sourced from Temu, excluding the [[Giotto Turbo Maxi|Giotto Turbo Maxi ]]. It also uses bolts as tips. The cost of the mod is ~4€; the price could vary depending on the price of the [[Giotto Turbo Maxi|Giotto Turbo Maxi]].

The mod’s construction is very simple, but it requires a circular file in order to make the parts fit each other easier. Also, using boiling water to stretch out the grips so they can fit the "cap" is recommended. And it is also strongly advised to use a pipe cutter for proper cuts on the body.

==Construction==

===Parts needed===
[[File:Temu mod demo 2.jpg]]
* 3x [[Giotto Turbo Maxi|Giotto Turbo Maxi]] (Barrel, Backplug)
* 1x Temu mod (grips)(can be subbed with DGG but has a noticeable difference of 3 grams and overall feel)
* 1x [[Crayola SuperTips|Crayola Supertip]] (barrel) or alternative with the same width
* 2x M8 30mm bolts
====Additional tools====
* Pipe cutter
* Paper tape
* Circular file
====Additional information====
[[File:Apogeum grip demo.jpg|thumb]]
* You can use the silicone bits that stick out on the Temu mod and use them as decorative grips.
* The weight can be adjusted. For lighter mod use, shorter M8s.
* The length can also be adjusted. If you want a longer mod, elongate the Giotto section that goes on the Giotto backplug, or take a shorter M8 eg 20mm M8 with 1 M8 nut.
* File or sand down the sharp edges on the bolt to avoid damaging the grips.
* You can also use silicone tubing or clear grip for a different design.

===Image Tutorial===

[[File:Apgg.jpg|left|thumb|300px|Image tutorial by Mervo. Click to expand]] 

[[Category:Pen Mods]]

Apogeum

2024-12-27T23:53:07Z

Krzys:

{{Mod Infobox
|name=Apogeum M8
|image={{#setmainimage:Apgmm.jpg}}
|creator= [[Mervo]]
|style= [[Double Sided]]
|length= 26cm
|weight= 50g
|cog=COP
}}
'''Apogeum M8''' (also known as The Lego Mod) is a bolt-tipped mod made by Polish [[PPP]]-based spinner [[Mervo]] in 2024. The mod is the 6th iteration since the original in 2019.
The mod is extremely cheap to make since it uses parts sourced from Temu, excluding the [[Giotto Turbo Maxi|Giotto Turbo Maxi ]]. It also uses bolts as tips. The cost of the mod is ~4€; the price could vary depending on the price of the [[Giotto Turbo Maxi|Giotto Turbo Maxi]].

The mod’s construction is very simple, but it requires a circular file in order to make the parts fit each other easier. Also, using boiling water to stretch out the grips so they can fit the "cap" is recommended. And it is also strongly advised to use a pipe cutter for proper cuts on the body.

==Construction==

===Parts needed===
[[File:Temu mod demo 2.jpg|thumb]]
* 3x [[Giotto Turbo Maxi|Giotto Turbo Maxi]] (Barrel, Backplug)
* 1x Temu mod (grips)(can be subbed with DGG but has a noticeable difference of 3 grams and overall feel)
* 1x [[Crayola SuperTips|Crayola Supertip]] (barrel) or alternative with the same width
* 2x M8 30mm bolts
====Additional tools====
* Pipe cutter
* Paper tape
* Circular file
====Additional information====
[[File:Apogeum grip demo.jpg|thumb]]
* You can use the silicone bits that stick out on the Temu mod and use them as decorative grips.
* The weight can be adjusted. For lighter mod use, shorter M8s.
* The length can also be adjusted. If you want a longer mod, elongate the Giotto section that goes on the Giotto backplug, or take a shorter M8 eg 20mm M8 with 1 M8 nut.
* File or sand down the sharp edges on the bolt to avoid damaging the grips.
* You can also use silicone tubing or clear grip for a different design.

===Image Tutorial===

[[File:Apgg.jpg|left|thumb|300px|Image tutorial by Mervo. Click to expand]] 

[[Category:Pen Mods]]

Apogeum

2024-12-06T13:50:17Z

Krzys:

{{Mod Infobox
|name=Apogeum M8
|image={{#setmainimage:Apgmm.jpg}}
|creator= [[Mervo]]
|style= [[Double Sided]]
|length= 26cm
|weight= 50g
|cog=COP
}}
'''Apogeum M8''' (also known as The Lego Mod) is an bolt tipped mod made by Polish [[PPP]] based spinner [[Mervo]] in 2024. The mod is the 6th iteration since the original in 2019.
The mod is extremely cheap to make since it uses parts sourced from Temu excluding the [[Giotto Turbo Maxi|Giotto Turbo Maxi ]], it also uses bolts as tips. The cost of the mod is ~4€ price could vary depending on the price of the [[Giotto Turbo Maxi|Giotto Turbo Maxi]].

The mod construction is very simple but it requires a circular file in order to make the parts fit eachother easier. Also using boiling water to stretch out the grips so they can fit the "cap" is recommended. And it is also strongly advised to use a pipe cutter for proper cuts or the body.

==Construction==

===Parts needed===
* 3x [[Giotto Turbo Maxi|Giotto Turbo Maxi]] (Barrel, Backplug)
*1x Temu mod (grips)(can be subbed with DGG but has a noticable diffrence of 3 grams and overall feel)
* 1x [[Crayola SuperTips|Crayola Supertip]] (barrel) or alternative with same width
* 2x M8 30mm Bolts
[[File:Temu mod demo 2.jpg|left|thumb|300px|The temu mod used ]] 
====Additional tools====
* Pipe cutter
* Paper tape
* Circular file
====Additional information====
* You can use the silicone bits that stick out on the temu mod and use it as decorative grips.
* The weight can be adjused. For lighter mod use shorter M8s.
* The lenght can also be adjusted, if you want a longer mod elongate glitto section that goes on giotto backplug, or take a shorter M8 eg 20mm M8 with 1 M8 nut.
* File or sand down the sharp edges on the bolt to avoid is damaging grips
* You can also use silicone tubing or clear grip for a diffrent design
[[File:Apogeum grip demo.jpg|left|thumb|300px|Temu mod silicone and silicone tubing used as decoration grips ]] 

===Image Tutorial===

[[File:Apgg.jpg|left|thumb|600px|Image tutorial by Mervo]] 

[[Category:Pen Mods]]

Apogeum

2024-12-06T13:49:05Z

Krzys:

{{Mod Infobox
|name=Apogeum M8
|image={{#setmainimage:Apgmm.jpg}}
|creator= [[Mervo]]
|style= [[Double Sided]]
|length= 26cm
|weight= 50g
|cog=COP
}}
'''Apogeum M8''' (also known as The Lego Mod) is an bolt tipped mod made by Polish [[PPP]] based spinner [[Mervo]] in 2024. The mod is the 6th iteration since the original in 2019.
The mod is extremely cheap to make since it uses parts sourced from Temu excluding the [[Giotto Turbo Maxi|Giotto Turbo Maxi ]], it also uses bolts as tips. The cost of the mod is ~4€ price could vary depending on the price of the [[Giotto Turbo Maxi|Giotto Turbo Maxi]].

The mod construction is very simple but it requires a circular file in order to make the parts fit eachother easier. Also using boiling water to stretch out the grips so they can fit the "cap" is recommended. And it is also strongly advised to use a pipe cutter for proper cuts or the body.

==Construction==

===Parts needed===
* 3x [[Giotto Turbo Maxi|Giotto Turbo Maxi]] (Barrel, Backplug)
*1x Temu mod (grips)(can be subbed with DGG but has a noticable diffrence of 3 grams and overall feel)
* 1x [[Crayola SuperTips|Crayola Supertip]] (barrel) or alternative with same width
* 2x M8 30mm Bolts
[[File:Temu mod demo 2.jpg|left|thumb|300px|The temu mod used ]] 
====Additional tools====
* Pipe cutter
* Paper tape
* Circular file
====Additional information====
* You can use the silicone bits that stick out on the temu mod and use it as decorative grips.
* The weight can be adjused. For lighter mod use shorter M8s.
* The lenght can also be adjusted, if you want a longer mod elongate glitto section that goes on giotto backplug, or take a shorter M8 eg 20mm M8 with 1 M8 nut.
* File or sand down the sharp edges on the bolt to avoid is damaging grips
* You can also use silicone tubing or clear grip for a diffrent design
[[File:Apogeum grip demo.jpg|left|thumb|300px|Temu mod silicone used as decoration grips ]] 

===Image Tutorial===

[[File:Apgg.jpg|left|thumb|600px|Image tutorial by Mervo]] 

[[Category:Pen Mods]]

File:Apogeum grip demo.jpg

2024-12-06T13:47:11Z

Krzys:

Apogeum grip demo

File:Apgmm.jpg

2024-12-06T13:45:31Z

Krzys:

apogeum mods

Apogeum

2024-11-23T00:20:38Z

Krzys:

{{Mod Infobox
|name=Apogeum M8
|image={{#setmainimage:Apogeum mod show.jpg}}
|creator= [[Mervo]]
|style= [[Double Sided]]
|length= 26cm
|weight= 50g
|cog=COP
}}
'''Apogeum M8''' (also known as The Lego Mod) is an bolt tipped mod made by Polish [[PPP]] based spinner [[Mervo]] in 2024. The mod is the 6th iteration since the original in 2019.
The mod is extremely cheap to make since it uses parts sourced from Temu excluding the [[Giotto Turbo Maxi|Giotto Turbo Maxi ]], it also uses bolts as tips. The cost of the mod is ~4€ price could vary depending on the price of the [[Giotto Turbo Maxi|Giotto Turbo Maxi]].

The mod construction is very simple but it requires a circular file in order to make the parts fit eachother easier. Also using boiling water to stretch out the grips so they can fit the "cap" is recommended. And it is also strongly advised to use a pipe cutter for proper cuts or the body.

==Construction==

===Parts needed===
* 3x [[Giotto Turbo Maxi|Giotto Turbo Maxi]] (Barrel, Backplug)
*1x Temu mod (grips)(can be subbed with DGG but has a noticable diffrence of 3 grams and overall feel)
* 1x [[Crayola SuperTips|Crayola Supertip]] (barrel) or alternative with same width
* 2x M8 30mm Bolts
[[File:Temu mod demo 2.jpg|left|thumb|300px|The temu mod used ]] 
====Additional tools====
* Pipe cutter
* Paper tape
* Circular file
====Additional information====
* You can use the silicone bits that stick out on the temu mod and use it as decorative grips
* The weight can be adjused. For lighter mod use shorter M8s.
* The lenght can also be adjusted, if you want a longer mod elongate glitto section that goes on giotto backplug, or take a shorter M8 eg 20mm M8 with 1 M8 nut.
* File or sand down the sharp edges on the bolt to avoid is damaging grips
[[File:Temu mod silicone as grips.jpg|left|thumb|300px|Temu mod silicone used as decoration grips ]] 

===Image Tutorial===

[[File:Apgg.jpg|left|thumb|600px|Image tutorial by Mervo]] 

[[Category:Pen Mods]]

Apogeum

2024-11-23T00:20:16Z

Krzys:

File:Apgg.jpg

2024-11-23T00:19:26Z

Krzys:

Apogeum

2024-11-17T22:25:37Z

Krzys:

{{Mod Infobox
|name=Apogeum M8
|image={{#setmainimage:Apogeum mod show.jpg}}
|creator= [[Mervo]]
|style= [[Double Sided]]
|length= 26cm
|weight= 50g
|cog=COP
}}
'''Apogeum M8''' (also known as The Lego Mod) is an bolt tipped mod made by Polish [[PPP]] based spinner [[Mervo]] in 2024. The mod is the 6th iteration since the original in 2019.
The mod is extremely cheap to make since it uses parts sourced from Temu excluding the [[Giotto Turbo Maxi|Giotto Turbo Maxi ]], it also uses bolts as tips. The cost of the mod is ~4€ price could vary depending on the price of the [[Giotto Turbo Maxi|Giotto Turbo Maxi]].

The mod construction is very simple but it requires a circular file in order to make the parts fit eachother easier. Also using boiling water to stretch out the grips so they can fit the "cap" is recommended. And it is also strongly advised to use a pipe cutter for proper cuts or the body.

==Construction==

===Parts needed===
* 3x [[Giotto Turbo Maxi|Giotto Turbo Maxi]] (Barrel, Backplug)
*1x Temu mod (grips)(can be subbed with DGG but has a noticable diffrence of 3 grams and overall feel)
* 1x [[Crayola SuperTips|Crayola Supertip]] (barrel) or alternative with same width
* 2x M8 30mm Bolts
[[File:Temu mod demo 2.jpg|left|thumb|300px|The temu mod used ]] 
====Additional tools====
* Pipe cutter
* Paper tape
* Circular file
====Additional inofmation====
* You can use the silicone bits that stick out on the temu mod and use it as decorative grips
* The weight can be adjused. For lighter mod use shorter M8s.
* The lenght can also be adjusted, if you want a longer mod elongate glitto section that goes on giotto backplug, or take a shorter M8 eg 20mm M8 with 1 M8 nut.
* File or sand down the sharp edges on the bolt to avoid is damaging grips
[[File:Temu mod silicone as grips.jpg|left|thumb|300px|Temu mod silicone used as decoration grips ]] 

===Image Tutorial===

[[File:APFI.jpg|left|thumb|600px|Image tutorial by Mervo]] 

[[Category:Pen Mods]]

Apogeum

2024-11-17T22:24:49Z

Krzys:

{{Mod Infobox
|name=Apogeum M8
|image={{#setmainimage:Apogeum mod show.jpg}}
|creator= [[Mervo]]
|style= [[Double Sided]]
|length= 26cm
|weight= 50g
|cog=COP
}}
'''Apogeum M8''' (also known as The Lego Mod) is an bolt tipped mod made by Polish [[PPP]] based spinner [[Mervo]] in 2024. The mod is the 6th iteration since the original in 2019.
The mod is extremely cheap to make since it uses parts sourced from Temu excluding the [[Giotto Turbo Maxi|Giotto Turbo Maxi ]], it also uses bolts as tips. The cost of the mod is ~4€ price could vary depending on the price of the [[Giotto Turbo Maxi|Giotto Turbo Maxi]].

The mod construction is very simple but it requires a circular file in order to make the parts fit eachother easier. Also using boiling water to stretch out the grips so they can fit the "cap" is recommended. And it is also strongly advised to use a pipe cutter for proper cuts or the body.

==Construction==

===Parts needed===
* 3x [[Giotto Turbo Maxi|Giotto Turbo Maxi]] (Barrel, Backplug)
*1x Temu mod (grips)(can be subbed with DGG but has a noticable diffrence of 3 grams and overall feel)
* 1x [[Crayola SuperTips|Crayola Supertip]] (barrel) or alternative with same width
* 2x M8 30mm Bolts
[[File:Temu mod demo 2.jpg|left|thumb|300px|The temu mod used ]] 
====Additional tools====
* Pipe cutter
* Paper tape
* Circular file
====Additional inofmation====
* You can use the silicone bits that stick out on the temu mod and use it as decorative grips
* The weight can be adjused. For lighter mod use shorter M8s.
* The lenght can also be adjusted, if you want a longer mod elongate glitto section that goes on giotto backplug, or take a shorter M8 eg 20mm M8 with 1 M8 nut.
[[File:Temu mod silicone as grips.jpg|left|thumb|300px|Temu mod silicone used as decoration grips ]] 

===Image Tutorial===

[[File:APFI.jpg|left|thumb|600px|Image tutorial by Mervo]] 

[[Category:Pen Mods]]

File:Temu mod silicone as grips.jpg

2024-11-17T22:23:16Z

Krzys:

demo on the how the temu mod silicone can be ulitlised

File:Temu mod demo 2.jpg

2024-11-17T22:22:20Z

Krzys:

Apogeum

2024-11-17T22:10:02Z

Krzys: /* Parts needed */

{{Mod Infobox
|name=Apogeum M8
|image={{#setmainimage:Apogeum mod show.jpg}}
|creator= [[Mervo]]
|style= [[Double Sided]]
|length= 26cm
|weight= 50g
|cog=COP
}}
'''Apogeum M8''' (also known as The Lego Mod) is an bolt tipped mod made by Polish [[PPP]] based spinner [[Mervo]] in 2024. The mod is the 6th iteration since the original in 2019.
The mod is extremely cheap to make since it uses parts sourced from Temu excluding the [[Giotto Turbo Maxi|Giotto Turbo Maxi ]], it also uses bolts as tips. The cost of the mod is ~4€ price could vary depending on the price of the [[Giotto Turbo Maxi|Giotto Turbo Maxi]].

The mod construction is very simple but it requires a circular file in order to make the parts fit eachother easier. Also using boiling water to stretch out the grips so they can fit the "cap" is recommended. And it is also strongly advised to use a pipe cutter for proper cuts or the body.

==Construction==

===Parts needed===
* 3x [[Giotto Turbo Maxi|Giotto Turbo Maxi]] (Barrel, Backplug)
*1x Temu mod (grips)(can be subbed with DGG but has a noticable diffrence of 3 grams and overall feel)
* 1x [[Crayola SuperTips|Crayola Supertip]] (barrel) or alternative with same width
* 2x M8 30mm Bolts
[[File:Temu mod.jpg|left|thumb|300px|The temu mod used (also comes in black) ]] 
====Additional tools====
* Pipe cutter
* Paper tape
* Circular file
====Additional inofmation====
* You can use the silicone bits that stick out on the temu mod and use it as decorative grips
* The weight can be adjused. For lighter mod use shorter M8s.
* The lenght can also be adjusted, if you want a longer mod elongate glitto section that goes on giotto backplug, or take a shorter M8 eg 20mm M8 with 1 M8 nut.

===Image Tutorial===

[[File:APFI.jpg|left|thumb|600px|Image tutorial by Mervo]] 

[[Category:Pen Mods]]

Apogeum

2024-11-17T22:09:25Z

Krzys:

{{Mod Infobox
|name=Apogeum M8
|image={{#setmainimage:Apogeum mod show.jpg}}
|creator= [[Mervo]]
|style= [[Double Sided]]
|length= 26cm
|weight= 50g
|cog=COP
}}
'''Apogeum M8''' (also known as The Lego Mod) is an bolt tipped mod made by Polish [[PPP]] based spinner [[Mervo]] in 2024. The mod is the 6th iteration since the original in 2019.
The mod is extremely cheap to make since it uses parts sourced from Temu excluding the [[Giotto Turbo Maxi|Giotto Turbo Maxi ]], it also uses bolts as tips. The cost of the mod is ~4€ price could vary depending on the price of the [[Giotto Turbo Maxi|Giotto Turbo Maxi]].

The mod construction is very simple but it requires a circular file in order to make the parts fit eachother easier. Also using boiling water to stretch out the grips so they can fit the "cap" is recommended. And it is also strongly advised to use a pipe cutter for proper cuts or the body.

==Construction==

===Parts needed===
* 3x [[Giotto Turbo Maxi|Giotto Turbo Maxi]] (Barrel, Backplug)
*1x Temu mod (grips)(can be subbed with DGG but has a noticable diffrence of 3 grams and overall feel)
* 1x [[Crayola SuperTips|Crayola Supertip]] (barrel) or alternative with same width
* 2x M8 30mm Bolts
[[File:Temu mod.jpg|left|thumb|300px|The temu mod used]] 
====Additional tools====
* Pipe cutter
* Paper tape
* Circular file
====Additional inofmation====
* You can use the silicone bits that stick out on the temu mod and use it as decorative grips
* The weight can be adjused. For lighter mod use shorter M8s.
* The lenght can also be adjusted, if you want a longer mod elongate glitto section that goes on giotto backplug, or take a shorter M8 eg 20mm M8 with 1 M8 nut.

===Image Tutorial===

[[File:APFI.jpg|left|thumb|600px|Image tutorial by Mervo]] 

[[Category:Pen Mods]]

SweSpin

2024-11-01T10:52:12Z

Krzys:

{{Community InfoBox
|name=SweSpin
|image={{#setmainimage:Swespinlogo.jpg}}
|country=Sweden
|language=Swedish
|founders=[[Ceedgee / måns (V1) NaabZer (V2)]]
|created= 6, April 2006
|website=[http://swespin.se/ swespin.se]
}}
'''SS''' or '''Swespin''' is the Swedish Pen Spinning Community.
==History==
In early 2006, Ceedgee discovered pen spinning. He later decided to start a Swedish pen spinning community, creating SweSpin.se on April 6, 2006, though he had already started work on the website about two weeks prior. It began as a shoutbox where he discussed his progress on the community and the website, mentioning Swedish tutorials, a trick-ranking system, and the first SweSpin CV, also edited by Ceedgee.

On April 18, the website went public, and on April 19, the first two SweSpin tutorials on the Bakaround and Thumbaround were published. On April 21, Ceedgee created a forum. SweSpin quickly gained popularity, releasing their first promo on May 12 and a CV in December. The last message from Ceedgee on the forum was posted on February 9, 2007, announcing the Pen Spinning World Tournament 2007 before the "reform," as he called it.

On August 23, 2007, Ceedgee revamped the website, transforming it into a portal style. He organized a meeting shortly after in Stockholm, Täby, which 17 people attended.

In November, when the Pen Spinning World Cup 2008 was announced, SweSpin formed a team consisting of sfsr, ålan, Ceedgee, bävern, hamor, and Pe/PDR. SweSpin advanced to the third round but ultimately lost to JEB. SweSpin remained active, regularly publishing CVs, promos, and holding gatherings.

In 2012, SweSpin started to decline, with fewer posts, videos, and less overall activity. This continued until 2014, when SweSpin.se was sold.

In 2015, NaabZer opened SweSpin V2 under the URL www.swespin.org and released a SweSpin revival collab and participated in Spinfest. SweSpin released new tutorials and organized gatherings. However, SweSpin remained largely inactive, with no new members joining and the same eight long-time members participating. In 2017, SweSpin.org was sold again.

==Collaboration Videos==
[https://www.youtube.com/watch?v=jeBGPpAKpI8&t=43s Spinfest 2016]

[https://www.youtube.com/watch?v=qPDBN2JVizM Swespin 2011 promo by dimhoLt]

[https://www.youtube.com/watch?v=BbsemJc_Cnk&t=151s First Swespin x FPSB collab]

[https://www.youtube.com/watch?v=mLJk0DhbFE4 2015 christmas cv]

[https://www.youtube.com/watch?v=HqZWpTqI4Cg 2009 Promo by Skinkpaj a swepsin moderator]

[https://www.youtube.com/watch?v=F5mf4kSj9Zk First swespin christmas collab]
==Competitive Spinning==
==References==
<references />
[[Category: Pen Spinning Communities]]

SweSpin

2024-11-01T10:51:55Z

Krzys:

{{Community InfoBox
|name=SweSpin
|image={{#setmainimage:Swespinlogo.jpg}}
|country=Sweden
|language=Swedish
|founders=[[Ceedgee / måns (V1)
NaabZer (V2)]]
|created= 6, April 2006
|website=[http://swespin.se/ swespin.se]
}}
'''SS''' or '''Swespin''' is the Swedish Pen Spinning Community.
==History==
In early 2006, Ceedgee discovered pen spinning. He later decided to start a Swedish pen spinning community, creating SweSpin.se on April 6, 2006, though he had already started work on the website about two weeks prior. It began as a shoutbox where he discussed his progress on the community and the website, mentioning Swedish tutorials, a trick-ranking system, and the first SweSpin CV, also edited by Ceedgee.

On April 18, the website went public, and on April 19, the first two SweSpin tutorials on the Bakaround and Thumbaround were published. On April 21, Ceedgee created a forum. SweSpin quickly gained popularity, releasing their first promo on May 12 and a CV in December. The last message from Ceedgee on the forum was posted on February 9, 2007, announcing the Pen Spinning World Tournament 2007 before the "reform," as he called it.

On August 23, 2007, Ceedgee revamped the website, transforming it into a portal style. He organized a meeting shortly after in Stockholm, Täby, which 17 people attended.

In November, when the Pen Spinning World Cup 2008 was announced, SweSpin formed a team consisting of sfsr, ålan, Ceedgee, bävern, hamor, and Pe/PDR. SweSpin advanced to the third round but ultimately lost to JEB. SweSpin remained active, regularly publishing CVs, promos, and holding gatherings.

In 2012, SweSpin started to decline, with fewer posts, videos, and less overall activity. This continued until 2014, when SweSpin.se was sold.

In 2015, NaabZer opened SweSpin V2 under the URL www.swespin.org and released a SweSpin revival collab and participated in Spinfest. SweSpin released new tutorials and organized gatherings. However, SweSpin remained largely inactive, with no new members joining and the same eight long-time members participating. In 2017, SweSpin.org was sold again.

==Collaboration Videos==
[https://www.youtube.com/watch?v=jeBGPpAKpI8&t=43s Spinfest 2016]

[https://www.youtube.com/watch?v=qPDBN2JVizM Swespin 2011 promo by dimhoLt]

[https://www.youtube.com/watch?v=BbsemJc_Cnk&t=151s First Swespin x FPSB collab]

[https://www.youtube.com/watch?v=mLJk0DhbFE4 2015 christmas cv]

[https://www.youtube.com/watch?v=HqZWpTqI4Cg 2009 Promo by Skinkpaj a swepsin moderator]

[https://www.youtube.com/watch?v=F5mf4kSj9Zk First swespin christmas collab]
==Competitive Spinning==
==References==
<references />
[[Category: Pen Spinning Communities]]

SweSpin

2024-11-01T10:50:33Z

Krzys:

{{Community InfoBox
|name=Swespin
|image={{#setmainimage:Swespinlogo.jpg}}
|country=Sweden
|language=Swedish
|founders=[[Ceedgee / måns]]
|created= 6, April 2006
|website=[http://swespin.se/ swespin.se]
}}
'''SS''' or '''Swespin''' is the Swedish Pen Spinning Community.
==History==
In early 2006, Ceedgee discovered pen spinning. He later decided to start a Swedish pen spinning community, creating SweSpin.se on April 6, 2006, though he had already started work on the website about two weeks prior. It began as a shoutbox where he discussed his progress on the community and the website, mentioning Swedish tutorials, a trick-ranking system, and the first SweSpin CV, also edited by Ceedgee.

On April 18, the website went public, and on April 19, the first two SweSpin tutorials on the Bakaround and Thumbaround were published. On April 21, Ceedgee created a forum. SweSpin quickly gained popularity, releasing their first promo on May 12 and a CV in December. The last message from Ceedgee on the forum was posted on February 9, 2007, announcing the Pen Spinning World Tournament 2007 before the "reform," as he called it.

On August 23, 2007, Ceedgee revamped the website, transforming it into a portal style. He organized a meeting shortly after in Stockholm, Täby, which 17 people attended.

In November, when the Pen Spinning World Cup 2008 was announced, SweSpin formed a team consisting of sfsr, ålan, Ceedgee, bävern, hamor, and Pe/PDR. SweSpin advanced to the third round but ultimately lost to JEB. SweSpin remained active, regularly publishing CVs, promos, and holding gatherings.

In 2012, SweSpin started to decline, with fewer posts, videos, and less overall activity. This continued until 2014, when SweSpin.se was sold.

In 2015, NaabZer opened SweSpin V2 under the URL www.swespin.org and released a SweSpin revival collab and participated in Spinfest. SweSpin released new tutorials and organized gatherings. However, SweSpin remained largely inactive, with no new members joining and the same eight long-time members participating. In 2017, SweSpin.org was sold again.

==Collaboration Videos==
[https://www.youtube.com/watch?v=jeBGPpAKpI8&t=43s Spinfest 2016]

[https://www.youtube.com/watch?v=qPDBN2JVizM Swespin 2011 promo by dimhoLt]

[https://www.youtube.com/watch?v=BbsemJc_Cnk&t=151s First Swespin x FPSB collab]

[https://www.youtube.com/watch?v=mLJk0DhbFE4 2015 christmas cv]

[https://www.youtube.com/watch?v=HqZWpTqI4Cg 2009 Promo by Skinkpaj a swepsin moderator]

[https://www.youtube.com/watch?v=F5mf4kSj9Zk First swespin christmas collab]
==Competitive Spinning==
==References==
<references />
[[Category: Pen Spinning Communities]]

SweSpin

2024-11-01T10:41:37Z

Krzys:

{{Community InfoBox
|name=Swespin
|image={{#setmainimage:Swespinlogo.jpg}}
|country=Sweden
|language=Swedish
|founders=[[Ceedgee / måns]]
|created= 6, April 2006
|website=[http://swespin.se/ swespin.se]
}}
'''SS''' or '''Swespin''' is the Swedish Pen Spinning Community.
==History==
In early 2006 [[Måns AKA Ceedgee]] discovered penspinning. He later on decided to start a swedish penspinning community and created SweSpin.se on the 6th of april, 2006, but having already started work on the website about 2 weeks prior. It started as a shoutbox talking about his progress on the community and the webiste, mentioning tutorials in swedish, trick ranking system and the first Swespin CV edited by also Ceedgee.

On the 18th of april the website went public and on the 19th published the first 2 swespin tutotials on the bakaround and thumbaround. The 21st or april he created a forum.
SweSpin became popular early on releasing their first promo on the 12th of may and also a CV in December.
Last message from Måns on the forum was posted on the 9th of february 2007 announcing [[Pen Spinning World Tournament 2007]] before the "reform" as he called it.

On the 23rd of August, 2007 Ceedgee revamped the website and turned it into a portal style. Ceedgee organised a meeting shortly after in stockholm, Täby to which 17 people attended.

In November when [[Pen Spinning World Cup 2008]] was announced swespin made team consisting of sfsr, ålan, ceedgee, bävern, hamor and Pe/PDR. Swespin went far and made it all the way to the third round, but ultimately losing to JEB. Swespin reamined active, publishing cvs, promos, having gatherings pretty rugulary.

In 2012 swespin started going on a decline, with less posts, less videos, and less activity. This continued until 2014 when the website SweSpin.se was sold.

In 2015 NaabZer opened up SweSpin V2 under the url www.swespin.org. And released [https://www.youtube.com/watch?v=QJM1k-ioehU a swespin revival collab] and [https://www.youtube.com/watch?v=jeBGPpAKpI8&t=43s partcicpated in spinfest]. Swespin released new tutorials, and orgianised new gatherings. Butt SweSpin still remained largely inactive with no new members. The community was the same 8 oldies. So in 2017 swepsin.org was sold again.

[[Category: Pen Spinning Communities]]

SweSpin

2024-11-01T00:25:08Z

Krzys:

SweSpin

2024-11-01T00:24:29Z

Krzys:

SweSpin

2024-11-01T00:21:26Z

Krzys:

SweSpin

2024-11-01T00:18:12Z

Krzys:

SweSpin

2024-10-31T23:56:41Z

Krzys:

SweSpin

2024-10-31T23:48:28Z

Krzys:

{{Community InfoBox
|name=Swespin
|image={{}}
|country=Sweden
|language=Swedish
|founders=[[Ceedgee / måns]]
|created= 6, April 2006
|website=[http://swespin.se/ swespin.se]
}}
'''SS''' or '''Swespin''' is the Swedish Pen Spinning Community.

[[Category: Pen Spinning Communities]]

SweSpin

2024-10-31T23:45:41Z

Krzys:

{{Community InfoBox
|name=Swespin
|image={{#setmainimage:
[[File:Swespinlogo|thumb]].png}}
|country=Sweden
|language=Swedish
|founders=[[Ceedgee / måns]]
|created= 6, April 2006
|website=[http://swespin.se/ swespin.se]
}}
'''SS''' or '''Swespin''' is the Swedish Pen Spinning Community.

[[Category: Pen Spinning Communities]]

SweSpin

2024-10-31T23:42:31Z

Krzys:

{{Community InfoBox
|name=Swespin
|image={{#setmainimage:swespinlogo.png}}
|country=Sweden
|language=Swedish
|founders=[[Hakan]], [[Dante]], [[Kmibar]]
|created= 6, April 2006
|website=[http://swespin.se/ swespin.se]
}}
'''SS''' or '''Swespin''' is the Swedish Pen Spinning Community.

[[Category: Pen Spinning Communities]]

File:Swespinlogo.jpg

2024-10-31T23:38:30Z

Krzys:

logo of swespin

SweSpin

2024-10-31T23:30:34Z

Krzys:

Swedish penspinning board

[[Category: Pen Spinning Communities]]

SweSpin

2024-10-31T23:27:41Z

Krzys: Created page with "Swedish penspinning board"

Swedish penspinning board

Apogeum

2024-10-12T00:24:40Z

Krzys:

{{Mod Infobox
|name=Apogeum M8
|image={{#setmainimage:Apogeum mod show.jpg}}
|creator= [[Mervo]]
|style= [[Double Sided]]
|length= 26cm
|weight= 50g
|cog=COP
}}
'''Apogeum M8''' (also known as The Lego Mod) is an bolt tipped mod made by Polish PPP based spinner [[Mervo]] in 2024. The mod is the 6th iteration since the original in 2019.
The mod is extremely cheap to make since it uses parts sourced from Temu excluding the [[Giotto Turbo Maxi|Giotto Turbo Maxi ]], it also uses bolts as tips. The cost of the mod is ~4€ price could vary depending on the price of the [[Giotto Turbo Maxi|Giotto Turbo Maxi]].

The mod construction is very simple but it requires a circular file in order to make the parts fit eachother easier. Also using boiling water to stretch out the grips so they can fit the "cap" is recommended. And it is also strongly advised to use a pipe cutter for proper cuts or the body.

==Construction==

===Parts needed===
* 3x [[Giotto Turbo Maxi|Giotto Turbo Maxi]] (Barrel, Backplug)
*1x Temu mod (grips)(can be subbed with DGG but has a noticable diffrence of 3 grams and overall feel)
* 1x [[Crayola SuperTips|Crayola Supertip]] (barrel) or alternative with same width
* 2x M8 30mm Bolts
[[File:Temu mod.jpg|left|thumb|300px|The temu mod used]] 
====Additional====
* Pipe cutter
* Paper tape
* Circular file

===Image Tutorial===

[[File:APFI.jpg|left|thumb|600px|Image tutorial by Mervo]] 

[[Category:Pen Mods]]

File:APFI.jpg

2024-10-12T00:22:02Z

Krzys:

Apogeum

2024-10-12T00:19:55Z

Krzys:

{{Mod Infobox
|name=Apogeum M8
|image={{#setmainimage:Apogeum mod show.jpg}}
|creator= [[Mervo]]
|style= [[Double Sided]]
|length= 26cm
|weight= 50g
|cog=COP
}}
'''Apogeum M8''' (also known as The Lego Mod) is an bolt tipped mod made by Polish PPP based spinner [[Mervo]] in 2024. The mod is the 6th iteration since the original in 2019.
The mod is extremely cheap to make since it uses parts sourced from Temu excluding the [[Giotto Turbo Maxi|Giotto Turbo Maxi ]], it also uses bolts as tips. The cost of the mod is ~4€ price could vary depending on the price of the [[Giotto Turbo Maxi|Giotto Turbo Maxi]].

The mod construction is very simple but it requires a circular file in order to make the parts fit eachother easier. Also using boiling water to stretch out the grips so they can fit the "cap" is recommended. And it is also strongly advised to use a pipe cutter for proper cuts or the body.

==Construction==

===Parts needed===
* 3x [[Giotto Turbo Maxi|Giotto Turbo Maxi]] (Barrel, Backplug)
*1x Temu mod (grips)(can be subbed with DGG but has a noticable diffrence of 3 grams and overall feel)
* 1x [[Crayola SuperTips|Crayola Supertip]] (barrel) or alternative with same width
* 2x M8 30mm Bolts
[[File:Temu mod.jpg|left|thumb|300px|The temu mod used]] 
====Additional====
* Pipe cutter
* Paper tape
* Circular file

===Image Tutorial===

[[File:Apogeum final.jpg|left|thumb|600px|Image tutorial by Mervo]] 

[[Category:Pen Mods]]

File:Apogeum final.png

2024-10-12T00:15:44Z

Krzys:

Apogeum

2024-10-07T22:05:18Z

Krzys:

{{Mod Infobox
|name=Apogeum M8
|image={{#setmainimage:Apogeum mod show.jpg}}
|creator= [[Mervo]]
|style= [[Double Sided]]
|length= 26cm
|weight= 50g
|cog=COP
}}
'''Apogeum M8''' (also known as The Lego Mod) is an bolt tipped mod made by Polish PPP based spinner [[Mervo]] in 2024. The mod is the 6th iteration since the original in 2019.
The mod is extremely cheap to make since it uses parts sourced from Temu excluding the [[Giotto Turbo Maxi|Giotto Turbo Maxi ]], it also uses bolts as tips. The cost of the mod is ~4€ price could vary depending on the price of the [[Giotto Turbo Maxi|Giotto Turbo Maxi]].

The mod construction is very simple but it requires a circular file in order to make the parts fit eachother easier. Also using boiling water to stretch out the grips so they can fit the "cap" is recommended. And it is also strongly advised to use a pipe cutter for proper cuts or the body.

==Construction==

===Parts needed===
* 3x [[Giotto Turbo Maxi|Giotto Turbo Maxi]] (Barrel, Backplug)
*1x Temu mod (grips)(can be subbed with DGG but has a noticable diffrence of 3 grams and overall feel)
* 1x [[Crayola SuperTips|Crayola Supertip]] (barrel) or alternative with same width
* 2x M8 30mm Bolts
[[File:Temu mod.jpg|left|thumb|300px|The temu mod used]] 
====Additional====
* Pipe cutter
* Paper tape
* Circular file

===Image Tutorial===

[[File:Apogeum mod tuttttt.jpg|left|thumb|600px|Image tutorial by Mervo]] 

[[Category:Pen Mods]]

File:Apogeum mod show.jpg

2024-10-07T22:04:02Z

Krzys:

File:Apogeum mod showcase.jpg

2024-10-07T22:01:16Z

Krzys:

kkk

Apogeum

2024-09-16T19:04:09Z

Krzys:

{{Mod Infobox
|name=Apogeum M8
|image={{#setmainimage:Apogeum mod.jpg}}
|creator= [[Mervo]]
|style= [[Double Sided]]
|length= 26cm
|weight= 50g
|cog=COP
}}
'''Apogeum M8''' (also known as The Lego Mod) is an bolt tipped mod made by Polish PPP based spinner [[Mervo]] in 2024. The mod is the 6th iteration since the original in 2019.
The mod is extremely cheap to make since it uses parts sourced from Temu excluding the [[Giotto Turbo Maxi|Giotto Turbo Maxi ]], it also uses bolts as tips. The cost of the mod is ~4€ price could vary depending on the price of the [[Giotto Turbo Maxi|Giotto Turbo Maxi]].

The mod construction is very simple but it requires a circular file in order to make the parts fit eachother easier. Also using boiling water to stretch out the grips so they can fit the "cap" is recommended. And it is also strongly advised to use a pipe cutter for proper cuts or the body.

==Construction==

===Parts needed===
* 3x [[Giotto Turbo Maxi|Giotto Turbo Maxi]] (Barrel, Backplug)
*1x Temu mod (grips)(can be subbed with DGG but has a noticable diffrence of 3 grams and overall feel)
* 1x [[Crayola SuperTips|Crayola Supertip]] (barrel) or alternative with same width
* 2x M8 30mm Bolts
[[File:Temu mod.jpg|left|thumb|300px|The temu mod used]] 
====Additional====
* Pipe cutter
* Paper tape
* Circular file

===Image Tutorial===

[[File:Apogeum mod tuttttt.jpg|left|thumb|600px|Image tutorial by Mervo]] 

[[Category:Pen Mods]]

File:Apogeum mod tuttttt.jpg

2024-09-16T19:03:08Z

Krzys:

Apogeum

2024-09-15T12:23:10Z

Krzys:

{{Mod Infobox
|name=Apogeum M8
|image={{#setmainimage:Apogeum mod.jpg}}
|creator= [[Mervo]]
|style= [[Double Sided]]
|length= 26cm
|weight= 50g
|cog=COP
}}
'''Apogeum M8''' (also known as The Lego Mod) is an bolt tipped mod made by Polish PPP based spinner [[Mervo]] in 2024. The mod is the 6th iteration since the original in 2019.
The mod is extremely cheap to make since it uses parts sourced from Temu excluding the [[Giotto Turbo Maxi|Giotto Turbo Maxi ]], it also uses bolts as tips. The cost of the mod is ~4€ price could vary depending on the price of the [[Giotto Turbo Maxi|Giotto Turbo Maxi]].

The mod construction is very simple but it requires a circular file in order to make the parts fit eachother easier. Also using boiling water to stretch out the grips so they can fit the "cap" is recommended. And it is also strongly advised to use a pipe cutter for proper cuts or the body.

==Construction==

===Parts needed===
* 3x [[Giotto Turbo Maxi|Giotto Turbo Maxi]] (Barrel, Backplug)
*1x Temu mod (grips)(can be subbed with DGG but has a noticable diffrence of 3 grams and overall feel)
* 1x [[Crayola SuperTips|Crayola Supertip]] (barrel) or alternative with same width
* 2x M8 30mm Bolts
[[File:Temu mod.jpg|left|thumb|300px|The temu mod used]] 
====Additional====
* Pipe cutter
* Paper tape
* Circular file

===Image Tutorial===

[[File:Apogeum mod tut full.jpg|left|thumb|600px|Image tutorial by Mervo]] 

[[Category:Pen Mods]]

File:Apogeum mod tut full.jpg

2024-09-15T12:21:25Z

Krzys:

updates version

Apogeum

2024-09-07T18:35:56Z

Krzys:

{{Mod Infobox
|name=Apogeum M8
|image={{#setmainimage:Apogeum mod.jpg}}
|creator= [[Mervo]]
|style= [[Double Sided]]
|length= 26cm
|weight= 50g
|cog=COP
}}
'''Apogeum M8''' (also known as The Lego Mod) is an bolt tipped mod made by Polish PPP based spinner [[Mervo]] in 2024. The mod is the 6th iteration since the original in 2019.
The mod is extremely cheap to make since it uses parts sourced from Temu excluding the [[Giotto Turbo Maxi|Giotto Turbo Maxi ]], it also uses bolts as tips. The cost of the mod is ~4€ price could vary depending on the price of the [[Giotto Turbo Maxi|Giotto Turbo Maxi]].

The mod construction is very simple but it requires a circular file in order to make the parts fit eachother easier. Also using boiling water to stretch out the grips so they can fit the "cap" is recommended. And it is also strongly advised to use a pipe cutter for proper cuts or the body.

==Construction==

===Parts needed===
* 3x [[Giotto Turbo Maxi|Giotto Turbo Maxi]] (Barrel, Backplug)
*1x Temu mod (grips)(can be subbed with DGG but has a noticable diffrence of 3 grams and overall feel)
* 1x [[Crayola SuperTips|Crayola Supertip]] (barrel) or alternative with same width
* 2x M8 30mm Bolts
[[File:Temu mod.jpg|left|thumb|300px|The temu mod used]] 
====Additional====
* Pipe cutter
* Paper tape
* Circular file

===Image Tutorial===

[[File:Apogeum mod tutorial.jpg|left|thumb|600px|Image tutorial by Mervo]] 

[[Category:Pen Mods]]

Apogeum

2024-09-06T20:24:06Z

Krzys:

{{Mod Infobox
|name=Apogeum M8
|image={{#setmainimage:Apogeum mod.jpg}}
|creator= [[Mervo]]
|style= [[Double Sided]]
|length= 26cm
|weight= 50g
|cog=COP
}}
'''Apogeum M8''' (also known as The Lego Mod) is an bolt tipped mod made by Polish PPP based spinner [[Mervo]] in 2024. The mod is the 6th iteration since the original in 2019.
The mod extremely cheap to make since it uses parts sourced from Temu excluding the [[Giotto Turbo Maxi|Giotto Turbo Maxi ]], it also uses bolts as tips. The cost of the mod is ~4€ price could vary depending on the price of the [[Giotto Turbo Maxi|Giotto Turbo Maxi pen]].

The mod construction is very simple but it requires a circular file in order to make the parts fit eachother easier. Also using boiling water to stretch out the grips so they can fit the "cap" is recommended. And it is also strongly advised to use a pipe cutter for proper cuts or the body.

==Construction==

===Parts needed===
* 3x [[Giotto Turbo Maxi|Giotto Turbo Maxi body]] (Barrel, Backplug)
*1x Temu mod (grips)(can be subbed with DGG but has a noticable diffrence of 3 grams and overall feel)
* 1x [[Crayola SuperTips|Crayola Supertip]] (barrel) or alternative with same width
* 2x M8 30mm Bolts
[[File:Temu mod.jpg|left|thumb|300px|The temu mod used]] 
====Additional====
* Pipe cutter
* Paper tape
* Circular file

===Image Tutorial===

[[File:Apogeum mod tutorial.jpg|left|thumb|600px|Image tutorial by Mervo]] 

[[Category:Pen Mods]]

Apogeum

2024-09-06T20:21:12Z

Krzys:

{{Mod Infobox
|name=Apogeum M8
|image={{#setmainimage:Apogeum mod.jpg}}
|creator= [[Mervo]]
|style= [[Double Sided]]
|length= 26.5cm
|weight= 50g
|cog=COP
}}
'''Apogeum M8''' (also known as The Lego Mod) is an bolt tipped mod made by Polish PPP based spinner [[Mervo]] in 2024. The mod is the 6th iteration since the original in 2019.
The mod extremely cheap to make since it uses parts sourced from Temu excluding the [[Giotto Turbo Maxi|Giotto Turbo Maxi ]], it also uses bolts as tips. The cost of the mod is ~3€ price could vary depending on the price of the [[Giotto Turbo Maxi|Giotto Turbo Maxi pen]].

The mod construction is very simple but it requires a circular file in order to make the parts fit eachother easier. Also using boiling water to stretch out the grips so they can fit the "cap" is recommended. And it is also strongly advised to use a pipe cutter for proper cuts or the body.

==Construction==

===Parts needed===
* 3x [[Giotto Turbo Maxi|Giotto Turbo Maxi body]] (Barrel, Backplug)
*1x Temu mod (grips)(can be subbed with DGG but has a noticable diffrence of 3 grams and overall feel)
* 1x [[Crayola SuperTips|Crayola Supertip]] (barrel) or alternative with same width
* 2x M8 30mm Bolts
[[File:Temu mod.jpg|left|thumb|300px|The temu mod used]] 
====Additional====
* Pipe cutter
* Paper tape
* Circular file

===Image Tutorial===

[[File:Apogeum mod tutorial.jpg|left|thumb|600px|Image tutorial by Mervo]] 

[[Category:Pen Mods]]