Fen Spinner Wiki - User contributions [en]

White Stick V2

2025-07-22T20:08:28Z

Garynotethan: /* Text Tutorial */

{{Mod Infobox
|name=White Stick V2
|image=
|creator= ProBloodBag
|style= [[Double Sided]]
|length= 24.5cm
|weight= ~21.7g
|cog=COP
}}
The '''[[White Stick V2]]''' is the second iteration of an aptly named mod made by [[ProBloodBag]]. The mod was made with a focus on minimalism in appearance and structure. Aside from the [[Tru Red Gripped Ballpoint Stick Pen]], all parts are relatively obtainable internationally, and the mod can be made for ~$10 USD at scale with most of the cost being attributed to the [[Pilot Opt Shaker]].

Cutting the silicone tubes has consistency issues due to curvature caused by the manufacturing process. Depending on wear, the tips may begin to come loose over time, but this can be fixed with new silicone tube grips, or increasing the length of the Tru Red grip segment.

Images coming soon. (hopefully)

==Construction==

===Parts needed===
* 3x [[Acrylic Paint Markers]] (barrel)
**Many duplicate subs, ensure 8.5cm length and 12mm OD
* 2x [[Pilot Opt Shaker]] (tip / sub-body)
* 1x [[Tru Red Gripped Ballpoint Stick Pen]] (cap / grip)
** Not available in all countries, any 10mm OD piece for center connecter and thin grip (heatshrink) can be subbed in
* 1x (9mm ID x 12mm OD) Food Grade Silicone Tube

===Text Tutorial===
# Cut 2 x 5mm Tru Red Ballpoint Stick Pen grip.
# Remove clip from Tru Red Ballpoint Stick Pen cap. The cap will be the connector.
# Disassemble the 3 Acrylic Paint Markers (remove ink and backplug).
# Cut 1.50cm from the back of one Acrylic Paint Marker for the center piece.
# Put the 1.50 Acrylic Paint Marker piece on the Tru Red Ballpoint Stick Pen cap and add some masking tape to both ends (Tape is folded over the ends if too long).
# Cut off the front from the other 2 Acrylic Paint Markers for the bodies.
# Remove the weird stuff from the inside of the barrel from the cut side (see [https://youtu.be/Vl1JAtD8r8A?t=917 15:17]). Scrape it out with pliers, knife, or round file until it is flush like a normal barrel.
# Disassemble your Pilot Opt/Nextage mechanical pencil.
# Take the sub-body (the part under the shell (coloured part)) and cut off the thinner part (part that is under the grip). Then cut 3.62cm from that end to remove the clicker and have a 3.62cm piece.
# File the inside of the 3.62cm sub-body piece from the tip side to increase the inner diameter and make it flush (see [https://youtu.be/Vl1JAtD8r8A?t=1520 25:20]). It should be perfectly smooth on the inside.
# Place the 5mm Tru Red Ballpoint Stick Pen grip on your Pilot Opt/Nextage tip. Place it inverted into the tip side of the 3.62 sub-body piece. The grip should be touching the end of the sub-body, not the base of the tip (see [https://youtu.be/Vl1JAtD8r8A?t=1581 26:21]). It is placed there to make the silhouette of the mod more flat and smooth. This is the "cap" of the pen.
# Cut 3.00cm of 9mm ID x 12mm OD silicone tube and place it over the "cap". There can be a small 1mm overhang from the silicon tube.
# Of course, make sure steps 7 - here are done twice for both sides of the mod.
# Connect bodies from the backplug side to the middle connector. Plug caps into the tip side of the bodies. White Stick V2 is complete.

=== Video Tutorial===
<youtube>https://youtu.be/Vl1JAtD8r8A?si=yU4VRmbvy_xT_0sl</youtube>

[[Category:Pen Mods]]

White Stick V2

2025-05-23T04:20:14Z

Garynotethan:

{{Mod Infobox
|name=White Stick V2
|image=
|creator= ProBloodBag
|style= [[Double Sided]]
|length= 24.5cm
|weight= ~21.7g
|cog=COP
}}
The '''[[White Stick V2]]''' is the second iteration of an aptly named mod made by '''[[ProBloodBag]]'''. The mod was made with a focus on minimalism in appearance and structure. Aside from the '''[[Tru Red Gripped Ballpoint Stick Pen]]''', all parts are relatively obtainable internationally, and the mod can be made for ~$10 USD at scale with most of the cost being attributed to the '''[[Pilot Opt Shaker]]'''.

Cutting the silicone tubes has consistency issues due to curvature caused by the manufacturing process. Depending on wear, the tips may begin to come loose over time, but this can be fixed with new silicone tube grips, or increasing the length of the Tru Red grip segment.

Images coming soon. (hopefully)

==Construction==

===Parts needed===
* 3x [[Acrylic Paint Markers]] (barrel)
**Many duplicate subs, ensure 8.5cm length and 12mm OD
* 2x [[Pilot Opt Shaker]] (tip / sub-body)
* 1x [[Tru Red Gripped Ballpoint Stick Pen]] (cap / grip)
** Not available in all countries, any 10mm OD piece for center connecter and thin grip (heatshrink) can be subbed in
* 1x (9mm ID x 12mm OD) Food Grade Silicone Tube

===Text Tutorial===
# Cut 2 x 5mm Tru Red Ballpoint Stick Pen grip.
# Remove clip from Tru Red Ballpoint Stick Pen cap. The cap will be the connector.
# Disassemble the 3 Acrylic Paint Markers (remove ink and backplug).
# Cut 1.50cm from the back of one Acrylic Paint Marker for the center piece.
# Put the 1.50 Acrylic Paint Marker piece on the Tru Red Ballpoint Stick Pen cap and add some masking tape to both ends (Tape is folded over the ends if too long).
# Cut off the front from the other 2 Acrylic Paint Markers for the bodies.
# Remove the weird stuff from the inside of the barrel from the cut side (see [https://youtu.be/Vl1JAtD8r8A?t=917 15:17]). Scrape it out with pliers, knife, or round file until it is flush like a normal barrel.
# Disassemble your Pilot Opt/Nextage mechanical pencil.
# Take the sub-body (the part under the shell (coloured part)) and cut off the thinner part (part that is under the grip). Then cut 3.62cm from that end to remove the clicker and have a 3.62cm piece.
# File the inside of the 3.62cm sub-body piece from the tip side to increase the inner diameter and make it flush (see [https://youtu.be/Vl1JAtD8r8A?t=1520 25:20]). It should be perfectly smooth on the inside.
# Place the 5mm Tru Red Ballpoint Stick Pen grip on your Pilot Opt/Nextage tip. Place it inverted into the tip side of the 3.62 sub-body piece. The grip should be touching the end of the sub-body, not the base of the tip (see [https://youtu.be/Vl1JAtD8r8A?t=1581 26:21]). It is placed there to make the silhouette of the mod more flat and smooth. This is the "cap" of the pen.
# Cut 3.00cm of 9mm ID x 12mm OD silicone tube and place it over the "cap". There can be a small 1mm overhang from the silicon tube.
# Of course, make sure steps 4 - here are done twice for both sides of the mod.
# Connect bodies from the backplug side to the middle connector. Plug caps into the tip side of the bodies. White Stick V2 is complete.

=== Video Tutorial===
<youtube>https://youtu.be/Vl1JAtD8r8A?si=yU4VRmbvy_xT_0sl</youtube>

[[Category:Pen Mods]]

White Stick V2

2025-05-22T20:32:00Z

Garynotethan: /* Construction */ text tutorial added

{{Mod Infobox
|name=White Stick V2
|image=
|creator= ProBloodBag
|style= [[Double Sided]]
|length= 24.5cm
|weight= ~21.7g
|cog=COP
}}
The '''[[White Stick V2]]''' is the second iteration of an aptly named mod made by '''[[ProBloodBag]]'''. The mod was made with a focus on minimalism in appearance and structure. Aside from the '''[[Tru Red Gripped Ballpoint Stick Pen]]''', all parts are relatively obtainable internationally, and the mod can be made for ~$10 USD at scale with most of the cost being attributed to the '''[[Pilot Opt Shaker]]'''.

Cutting the silicone tubes has consistency issues due to curvature caused by the manufacturing process. Depending on wear, the tips may begin to come loose over time, but this can be fixed with new silicone tube grips, or increasing the length of the Tru Red grip segment.

Images coming soon. (hopefully)

==Construction==

===Parts needed===
* 3x [[Acrylic Paint Markers]] (barrel)
**Many duplicate subs, ensure 8.5cm length and 12mm OD
* 2x [[Pilot Opt Shaker]] (tip / sub-body)
* 1x [[Tru Red Gripped Ballpoint Stick Pen]] (cap / grip)
** Not available in all countries, any 10mm OD piece for center connecter and thin grip (heatshrink) can be subbed in
* 1x (9mm ID x 12mm OD) Food Grade Silicone Tube

===Text Tutorial===
# Cut 2 x 5mm Tru Red Ballpoint Stick Pen grip.
# Remove clip from Tru Red Ballpoint Stick Pen cap. The cap will be the connector.
# Disassemble the 3 Acrylic Paint Markers (remove ink and backplug).
# Cut 1.50cm from the back of one Acrylic Paint Marker for the center piece.
# Put the 1.50 Acrylic Paint Marker piece on the Tru Red Ballpoint Stick Pen cap and add some masking tape to both ends (Tape is folded over the ends if too long).
# Cut off the front from the other 2 Acrylic Paint Markers for the bodies.
# Remove the weird stuff from the inside of the barrel from the cut side (see [https://youtu.be/Vl1JAtD8r8A?t=917 15:17]). Scrape it out with pliers, knife, or round file until it is flush like a normal barrel.
# Disassemble your Pilot Opt/Nextage mechanical pencil.
# Take the sub-body (the part under the shell (coloured part)) and cut off the thinner part (part that is under the grip). Then cut 3.62cm from that end to remove the clicker and have a 3.62cm piece.
# File the inside of the 3.62cm sub-body piece from the tip side to increase the inner diameter and make it flush (see [https://youtu.be/Vl1JAtD8r8A?t=1520 25:20]). It should be perfectly smooth on the inside.
# Place the 5mm Tru Red Ballpoint Stick Pen grip on your Pilot Opt/Nextage tip. Place it inverted into the tip side of the 3.62 sub-body piece. The grip should be touching the end of the sub-body, not the base of the tip (see [https://youtu.be/Vl1JAtD8r8A?t=1581 26:21]). It is placed there to make the silhouette of the mod more flat and smooth. This is the "cap" of the pen.
# Cut 3.00cm of 9mm ID x 12mm OD silicone tube and place it over the "cap". There can be a small 1mm overhang from the silicon tube.
# Connect bodies from the backplug side to the middle connector. Plug caps into the tip side of the bodies. White Stick V2 is complete.

=== Video Tutorial===
<youtube>https://youtu.be/Vl1JAtD8r8A?si=yU4VRmbvy_xT_0sl</youtube>

[[Category:Pen Mods]]

White Stick V2

2025-05-22T18:42:33Z

Garynotethan: /* Tutorial */

White Stick V2

2025-05-20T19:38:03Z

Garynotethan:

Menowa* Mod

2022-01-17T17:49:18Z

Garynotethan: somebody fix the grammar of this one sentence i added im literally in kindergarten bro

{{Mod Infobox
|name=Menowa* Mod
|image={{#setmainimage:menowa mod oleg.png}}
|creator= Menowa*
|style= [[Double Sided]]
|length= 20cm
|weight= 20g
|cog=COP
}}
'''Menowa* Mod''' is a dense yet short mod created by [[Menowa*]] and popularized during his success, earning itself self a spot as one of the most iconic and popular double-sided mods.
If you wanted to be specific, there is currently 3-4 different versions of Menowa Mod.

==Construction==
===Parts needed===

* 2x [[Pilot Dr. Grip HDG-50R|Dr. Grip]] (tips)
* 4x [[Dong-A Anyball|Anyball]] (grips)
* 2x [[Pilot Airblanc|Airblanc]] (tips)
* 2x [[Keityo Sign Pen|KT]] (caps)
* 1x [[Bic Round Stic Grip]] (barrel)
* 2x [[Crayola Supertip|ST]] (Old ST -> thick version) (barrels)
* 1x [[Zebra Hyper Jell]] (grip)

* 2x [[Pilot G3]] (Rubber stopper from inside cap) --> Optional
* 2x [[Zebra Airfit]] (Metal rings) --> Optional
* 2x [[Muji Tect2way]] (4 silicon rings - clear) --> Optional
* 2x [[Zebra Tect2way]] (5 silicon rings - black) --> Optional

===Video tutorial===
<youtube>https://youtu.be/OWg-PRldNiU</youtube>

Video tutorial by VORE-TEX.

==References==

[[Category: Pen Mods]]

Kagami DC

2022-01-16T22:30:38Z

Garynotethan: added backplugs to part list

{{Mod Infobox
|name=Kagami DC
|image={{#setmainimage:Kagami_DC.png}}
|creator= Kagami
|style= [[Double Sided]]
|length= 21cm
|weight= ~14.5g
|cog=COP
}}
The '''Kagami DC''' is a mod created and popularized by [[Kagami]]. Despite its asymmetric design, it's still known as a double sided mod.

==Construction==
===Parts needed===

* 1x [[Ace Art Color Twin|ACT]] (cap, barrel, backplug)
* 1x [[Pentel Color Twin|CT]] (cap, backplug)
* 2x [[Zebra Sarasa|Old Sarasa]] (grip)
* 1x [[Pilot SuperGrip|SuperGrip]] (grip)
* 1x [[Dong-a Anyball|Anyball]] (grip)
* 2x [[Pilot Vega Gel]] (tip)

===Text tutorial===
# Disassemble the ACT fully leaving only the body.
# Hollow both the large CT cap and the large ACT cap.
# Cut down both the smaller caps until they are the same length as the ACT backplug.
# Tightly fit the smaller ACT cap on the back of the ACT body and the smaller CT cap on front.
# Cut each of the Sarasa grips down to 2 cm.
# Cut 1 section of 2 rings of Anyball.
# Cut 2 sections of 1 ring of SuperGrip.
# Place the Anyball section on the smaller CT cap.
# Unscrew the tips from the Pilot Vega Gel and place them in both the larger caps.
# Place each of the SuperGrip rings into one Sarasa grip, then place one on the end of each larger cap.
# Place the larger caps on the two ends of the body.

Tutorial assembled from Kagami's YouTube tutorial and Penmodding.pm<ref>[https://penmodding.pm/archives/5843 Penmodding.pm tutorial]</ref>.

===Video tutorial===
<youtube>https://youtu.be/pQP_cFYoZqg</youtube>

Video tutorial by Kagami.

==References==

[[Category: Pen Mods]]

Motsuun pen

2022-01-13T19:39:41Z

Garynotethan:

{{Mod Infobox
|name=
|image=Motsuunpen.jpg
|creator= [[Meves]]
|style= [[Double Sided]]
|length= 19cm
|weight= 15.7g
|cog=COP
}}
'''Motsuun pen''' is a mod made by [[Meves]] (Mizu) from the [[JEB]] community. It was popularized by [[Mesi]]'s usage of the mod.

==Construction==

===Parts Needed===
List from Meves' YouTube Channel:<ref name="motuun JEB">https://youtu.be/FZZ17hsdxIU</ref>
* 1x [[Supertip]] (barrel)
* 2x [[Keityou Sign Pen|KT]] (caps)
* 1x [[Dr. Grip]] (grip)
* 1x [[Zebra Sarasa|Sarasa]] (grip)
* 1x [[Tombow Playcolor2|PC2]] (backplug)
* 2x [[Signo]] (tips)

===Text Tutorial===
# Cut Dr. Grip grip in half.
# Cut Sarasa grip in half.
# Empty SuperTip barrel by removing marker and backplug.
# Insert PC2 backplug in the back of the SuperTip barrel.
# Screw signo tips at the end of the KT caps.
# Place the Sarasa grips on both caps and push down. [[File:Motsuun1.JPG|left|thumb|200px]] 
# Place the Dr. Grip grips on the extra space on both caps. (signo rip ptrudes around 5mm) [[File:Motsuun2.JPG|left|thumb|200px]] 
# Place both caps on each side of the SuperTip barrel; done.

===Video Tutorial===
<youtube>https://youtu.be/FZZ17hsdxIU</youtube>

==References==
<references />

[[Category:Pen Mods]]

Hash Comssa

2022-01-13T19:32:16Z

Garynotethan:

{{Mod Infobox
|name=
|image=Hashcomssa.JPG
|creator= [[Hash]]
|style= [[Double Sided]]
|length= 21cm
|weight= 14g
|cog=
}}

'''Hash Comssa''' is a [[Dong-A Computer Sign Pen|Comssa]] based mod created by [[JEB]] spinner [[Hash]]. It is a well known mod due to it being quite simple to make, along with it also spinning well. Please note that the original uses [[bellcolor]] instead of comssa and hi-tec-c instead of [[signo]].

==Construction==

===Parts needed===
* 1x [[Zebra Airfit BA-9|Airfit]] (grip)
* 2x [[Dong-A Computer Sign Pen|Comssa]] (caps and one barrel)
* 2x [[Signo]] (tips)

===Text tutorial===
# Empty out one Comssa barrel by removing the marker's tips and backplug. Return the backplug to the marker after removing the ink.
# Place the other Comssa cap on the backplug side of the barrel to double cap it. (tape around the comssa backplug area is recommended to increase the width of the barrel and prevent the cap from falling off)
# Cut Airfit grip in half.
# Place the Airfit grips onto both sides of the caps on the barrel.
# Place the Signo tips onto both sides of the Airfit grips and the mod is finished.

===Video tutorial===
<youtube>https://youtu.be/xV6xObyePw0</youtube>

Video tutorial by Oleg.

[[Category: Pen Mods]]

Minwoo Mod

2022-01-13T19:29:34Z

Garynotethan:

{{Mod Infobox
|name=
|image=Minwoomod.JPG
|creator= [[Minwoo]]
|style= [[Double Sided]]
|length= 20.8cm
|weight= 18g
|cog=
}}
'''Minwoo Mod''' is a personal mod made by the spinner [[Minwoo]]. It is known for its usage by Minwoo in the [[Pen Spinning World Tournament 2009]].

==Construction==

===Parts needed===
* 1x [[Dr. Grip Shaker|Dr. Grip]] (tip and grip)
* 1x [[Pilot G3|G3]] (tip; metal)
* 1x [[Super Pirat]] (barrel)
* 1x [[Sailor IC Liquid Gel|Sailor]] (grip)
* 1x [[Dong-A Comssa|Comssa]] (cap)
* 1x [[Penwish Ring]] (ring)
* 1x [[Faber Castell Gripmatic Mechanical Pencil|Gripmatic]] (grip/section/ring)

===Text tutorial===
# Cut 2 sections of sailor grip. [[File:Minwoomod1.JPG|left|thumb|200px]] 
# Take the Dr. Grip tip and grip from the pen, then, cut 2.5cm from the back of the grip. (the lip side of the Dr Grip Grip needs to be 2.5cm) [[File:Minwoomod2.JPG|left|thumb|200px]] 
# Attach the sailor grip and Dr. Grip grip into the comssa cap, then insert the Dr. Grip tip. [[File:Minwoomod3.JPG|left|thumb|200px]] 
# Place the penwish ring between the Dr Grip tip and grip. [[File:Minwoomod4.JPG|left|thumb|200px]] 
# Hollow out super pirat barrel and use nail polish to clean the barrel. [[File:Minwoomod5.JPG|left|thumb|200px]] 
# Use electrical tape to increase width of barrel for later use. [[File:Minwoomod6.JPG|left|thumb|200px]] 
# Unscrew the metal tip from the G3, remove the clip and the in-plug of the G3 cap. [[File:Minwoomod7.JPG|left|thumb|200px]] 
# Place gripmatic tip in G3 cap.
# Cut two sections of sailor grip.
# Cut 1.2cm from Dr. Grip grip. [[File:Minwoomod8.JPG|left|thumb|200px]] 
# Cut one section of gripmatic, we will be using the rest of the 8 sections. [[File:Minwoomod9.JPG|left|thumb|200px]] 
# Place G3 tip on the 8 gripmatic section.
# An insert with the dimensions of 3.6cm to 2.5cm is optional.
# Place the gripmatic 8 section into the G3 cap. [[File:Minwoomod10.JPG|left|thumb|200px]] 
# Place the two section sailor and the Dr. Grip grip over the cap. [[File:Minwoomod11.JPG|left|thumb|200px]] 
# Connect front cap and back cap to body and the mod is finished.

===Video tutorial===
<youtube>https://youtu.be/Sk6f6FYsr3I</youtube>

Video tutorial by Minwoo.

[[Category: Pen Mods]]

Huwng KT

2022-01-13T19:28:24Z

Garynotethan:

{{Mod Infobox
|name=
|image=Huwng 4.jpg
|creator= [[Huwng]]
|style= [[Double Sided]]
|length= 22cm
|weight= 14g
|cog=COP
}}
'''Huwng KT''' is a mod made by [[Huwng]] from [[VNPS]].
The original mod is specifically made out of Oasis CT Caps, Eno hi-tec-c tips, and old thick golden text supertips. The original tutorial can be found [https://caotienhung.blogspot.com/2021/11/personal-kt.html here.]
==Construction==

===Parts Needed===
List from a now deleted video by Huwng
* 2x [[Supertip]] (Barrels)
* 2x [[ColorTwin]] (Caps)
* 2x [[Hi-tec-C]] (Tips)
* 2x [[Dr. Grip]] (grips)
* 1x [[Eno ST Connector]] or [[Bic Round Stic]] (Barrel)

===Text Tutorial===
# Cut the Dr grip grips 2.1cm from the lip side.
# Take the CT caps and hammer the Hi Tec C tips into them. [[File:Huwng 1.jpg|left|thumb|200px]] 
# Put the Dr. Grip grips over the front of caps and tips
# Cut both of the ST barrels to 6.4 cm from the front [[File:Huwng 2.jpg|left|thumb|200px]] 
# Connect the ST barrels with the ST connector or a small piece of bic barrel [[File:Huwng 3.jpg|left|thumb|200px]] 
# Put caps on the body and you are done! [[File:Huwng 4.jpg|left|thumb|200px]] 

[[Category:Pen Mods]]

Huwng KT

2022-01-13T19:27:07Z

Garynotethan:

{{Mod Infobox
|name=
|image=Huwng 4.jpg
|creator= [[Huwng]]
|style= [[Double Sided]]
|length= 22cm
|weight= 14g
|cog=COP
}}
'''Huwng KT''' is a mod made by [[Huwng]] from [[VNPS]].
The original mod is specifically made out of Oasis CT Caps, Eno hi-tec-c tips, and old thick golden text supertips. The original tutorial can be found [https://caotienhung.blogspot.com/2021/11/personal-kt.html here.]
==Construction==

===Parts Needed===
List from a now deleted video by Huwng
* 2x [[Supertip]] (Barrels)
* 2x [[ColorTwin]] (Caps)
* 2x [[Hi-tec-C]] (Tips)
* 2x [[Dr. Grip]] (grips)
* 1x [[Eno ST Connector]] or [[Bic Round Stic]] (Barrel)

===Text Tutorial===
# Cut the Dr grip grips in half
# Take the CT caps and hammer the Hi Tec C tips into them. [[File:Huwng 1.jpg|left|thumb|200px]] 
# Put the Dr. Grip grips over the front of caps and tips
# Cut both of the ST barrels to 6.5 cm from the front [[File:Huwng 2.jpg|left|thumb|200px]] 
# Connect the ST barrels with the ST connector or a small piece of bic barrel [[File:Huwng 3.jpg|left|thumb|200px]] 
# Put caps on the body and you are done! [[File:Huwng 4.jpg|left|thumb|200px]] 

[[Category:Pen Mods]]

Huwng KT

2022-01-13T19:26:48Z

Garynotethan:

{{Mod Infobox
|name=
|image=Huwng 4.jpg
|creator= [[Huwng]]
|style= [[Double Sided]]
|length= 22cm
|weight= 14g
|cog=COP
}}
'''Huwng KT''' is a mod made by [[Huwng]] from [[VNPS]].
The original mod is specifically made out of Oasis CT Caps, Eno hi-tec-c tips, and old thick golden text supertips. Original tut can be found [https://caotienhung.blogspot.com/2021/11/personal-kt.html here.]
==Construction==

===Parts Needed===
List from a now deleted video by Huwng
* 2x [[Supertip]] (Barrels)
* 2x [[ColorTwin]] (Caps)
* 2x [[Hi-tec-C]] (Tips)
* 2x [[Dr. Grip]] (grips)
* 1x [[Eno ST Connector]] or [[Bic Round Stic]] (Barrel)

===Text Tutorial===
# Cut the Dr grip grips in half
# Take the CT caps and hammer the Hi Tec C tips into them. [[File:Huwng 1.jpg|left|thumb|200px]] 
# Put the Dr. Grip grips over the front of caps and tips
# Cut both of the ST barrels to 6.5 cm from the front [[File:Huwng 2.jpg|left|thumb|200px]] 
# Connect the ST barrels with the ST connector or a small piece of bic barrel [[File:Huwng 3.jpg|left|thumb|200px]] 
# Put caps on the body and you are done! [[File:Huwng 4.jpg|left|thumb|200px]] 

[[Category:Pen Mods]]

Huwng KT

2022-01-13T19:24:36Z

Garynotethan:

{{Mod Infobox
|name=
|image=Huwng 4.jpg
|creator= [[Huwng]]
|style= [[Double Sided]]
|length= 22cm
|weight= 14g
|cog=COP
}}
'''Huwng KT''' is a mod made by [[Huwng]] from [[VNPS]].
The original mod is specifically made out of Oasis CT Caps, Eno hi-tec-c tips, and old thick golden text supertips.

==Construction==

===Parts Needed===
List from a now deleted video by Huwng
* 2x [[Supertip]] (Barrels)
* 2x [[ColorTwin]] (Caps)
* 2x [[Hi-tec-C]] (Tips)
* 2x [[Dr. Grip]] (grips)
* 1x [[Eno ST Connector]] or [[Bic Round Stic]] (Barrel)

===Text Tutorial===
# Cut the Dr grip grips in half
# Take the CT caps and hammer the Hi Tec C tips into them. [[File:Huwng 1.jpg|left|thumb|200px]] 
# Put the Dr. Grip grips over the front of caps and tips
# Cut both of the ST barrels to 6.5 cm from the front [[File:Huwng 2.jpg|left|thumb|200px]] 
# Connect the ST barrels with the ST connector or a small piece of bic barrel [[File:Huwng 3.jpg|left|thumb|200px]] 
# Put caps on the body and you are done! [[File:Huwng 4.jpg|left|thumb|200px]] 

[[Category:Pen Mods]]

Kagami DC

2022-01-13T19:13:27Z

Garynotethan:

{{Mod Infobox
|name=Kagami DC
|image={{#setmainimage:Kagami_DC.png}}
|creator= Kagami
|style= [[Double Sided]]
|length= 21cm
|weight= ~14.5g
|cog=COP
}}
'''Kagami DC''' is a mod created and popularized by [[Kagami]], but despite its asymmetric design it's still known as a double sided mod.

==Construction==
===Parts needed===

* 1x [[Ace Art Color Twin]]
* 1x [[Pentel Color Twin]]
* 2x [[Zebra Sarasa (Old)]]（grip）
* 1x [[Pilot Supergrip]]（grip - you only need the rings section）
* 1x [[Dong-a Anyball]]（grip）
* 2x [[Pilot Vega Gel]]（tip）

===Text tutorial===
# Disassemble the Pentel Art Color Twin fully leaving only the body.
# Hollow both the large Color Twin cap and the large Art Color cap.
# Cut down both the smaller caps until they are the same length as the Art Color backplug.
# Tightly fit the smaller Art Color cap on the back of the Art Color body and the smaller Color Twin cap on front.
# Cut each of the Zebra Sarasa grips down to 2 cm.
# Cut 1 section of 2 rings of Dong-a Anyball.
# Cut 2 sections of 1 ring of Pilot Supergrip.
# Place the Dong-a Anyball section on the smaller Color Twin cap.
# Unscrew the tips from the Pilot Vega Gel and place them in both the larger caps.
# Place each of the Supergrip rings into one Sarasa grip, then place one on the end of each larger cap.
# Place the larger caps on the two ends of the body.

Tutorial assembled from Kagami's YouTube Video Tutorial (Below) and [[VORE-TEX]]'s blog<ref>https://penmodding.pm/archives/5843</ref>.

===Video tutorial===
<youtube>https://youtu.be/pQP_cFYoZqg</youtube>

Video tutorial by Kagami Kirishima.

[[Category: Pen Mods]]